1. Produktas baigtasview
The Nidec Servo GentleTyphoon D1225C12B6ZPA is a 120mm case fan designed for efficient cooling with reduced noise. It features a double ball bearing for extended lifespan and an optimized fan blade design for high static pressure and airflow. This fan incorporates a newly developed motor with a double vibration reduction structure and dampening rings to minimize operational noise.
Image 1: Nidec Servo GentleTyphoon 120mm Case Fan, front view.
Pagrindinės funkcijos:
- High airflow volume and low noise due to newly designed impeller.
- Fan propeller engineered to reduce disturbing frequency fan noise.
- Double vibration reduction structure in motor and support mechanism.
- 4-pin PWM connector for variable speed control (900-2150 RPM).
- Double ball bearing for a long operational life (up to 100,000 hours at 35°C).
2. Sąranka ir diegimas
This section provides general guidelines for installing the Nidec Servo GentleTyphoon 120mm case fan. Specific installation procedures may vary depending on your computer case or cooling system.
- Paruošimas: Ensure your computer is powered off and unplugged from the wall outlet. Open your computer case to access the fan mounting locations.
- Montavimas: Position the fan in the desired location (e.g., front intake, rear exhaust, top exhaust, or on a radiator). Ensure the fan's airflow direction is correct for your cooling strategy. The fan typically has an arrow indicating airflow direction on its side. Secure the fan using appropriate screws (not included with this OEM version).
- Ryšys: Connect the fan's 4-pin PWM connector to an available 4-pin fan header on your motherboard. Refer to your motherboard manual for fan header locations. The 4-pin connector allows the motherboard to control the fan speed based on system temperature.
- Kabelių valdymas: Ventiliatoriaus laidą išdėstykite tvarkingai, kad netrukdytų kitiems komponentams ar oro srautui.
- Galutinis patikrinimas: Before closing the case, double-check all connections and ensure no cables are obstructing the fan blades.
Smeigtuko konfigūracija:
The 4-pin PWM connector follows a standard pinout for fan control:
- 1. Black: Žemė (GND)
- 2. Raudona: Power (+V)
- 3. Yellow: Sensor (RPM signal)
- 4. Mėlyna: Control (PWM signal)
Image 2: Technical diagram showing fan dimensions, pin configuration, and lead specifications.
3. Naudojimo instrukcijos
Once installed, the fan will operate automatically when the computer is powered on. The 4-pin PWM connection allows your motherboard to dynamically adjust the fan speed based on system temperature, optimizing for both cooling performance and noise levels.
- Automatinis valdymas: Most modern motherboards will automatically detect and control PWM fans. You can typically configure fan curves in your motherboard's BIOS/UEFI settings or through manufacturer-provided software.
- Greičio diapazonas: The fan operates within a speed range of 900 to 2150 RPM. At lower RPMs, the fan is designed for quiet operation, while higher RPMs provide maximum airflow for demanding tasks.
- Noise Characteristics: The GentleTyphoon fan is engineered to produce a less intrusive sound profile compared to conventional fans, even at higher speeds, by reducing disturbing frequency fan noise.
4. Priežiūra
Reguliarus techninis aptarnavimas padeda užtikrinti optimalų ventiliatoriaus veikimą ir pailgina jo tarnavimo laiką.
- Valymas: Periodically clean dust accumulation from the fan blades and housing. Use compressed air or a soft brush. Ensure the fan is powered off and unplugged before cleaning. Hold the fan blades gently to prevent them from spinning rapidly during cleaning, which can damage the bearing.
- Patikra: Check for any obstructions around the fan. Ensure cables are not touching the blades. Listen for unusual noises, which could indicate a problem with the bearing or an obstruction.
- Guolis: The double ball bearing is designed for long-term, maintenance-free operation. No lubrication is required.
5. Problemų sprendimas
If you encounter issues with your Nidec Servo GentleTyphoon fan, refer to the following troubleshooting steps:
- Ventiliatorius nesisuka:
- Ensure the 4-pin connector is securely plugged into the motherboard fan header.
- Check your motherboard's BIOS/UEFI settings to ensure the fan header is enabled and configured correctly (e.g., not set to 0 RPM at low temperatures if you expect it to spin).
- Patikrinkite, ar maitinimo šaltinis veikia tinkamai.
- Per didelis triukšmas:
- Inspect the fan for any obstructions (e.g., loose cables, dust buildup) that might be hitting the blades.
- Įsitikinkite, kad ventiliatorius yra tvirtai pritvirtintas ir nevibruoja į korpusą ar kitus komponentus.
- Check fan speed settings in BIOS/UEFI. High RPMs will naturally produce more airflow noise. Adjust the fan curve to a lower speed if noise is a primary concern and temperatures allow.
- While designed for reduced noise, some operational sound is normal, especially at higher speeds.
- Mažas oro srautas:
- Verify the fan is spinning in the correct direction for its intended purpose (intake or exhaust).
- Clean any dust from the fan blades and any filters in front of or behind the fan.
- Check fan speed settings in BIOS/UEFI. Ensure the fan is operating at an appropriate RPM for the cooling demands.
6. Specifikacijos
| Funkcija | Detalė |
|---|---|
| Modelis | D1225C12B6ZPA |
| Matmenys (I x P x A) | 120 mm x 120 mm x 25 mm (0.98 colio ilgio x 4.72 colio pločio x 4.72 colio aukščio) |
| Ventiliatoriaus greitis | 900–2150 aps./min. |
| Oro srauto talpa | 20 - 68 CFM (Cubic Feet Per Minute) |
| Triukšmo lygis | 15 - 34 dB max |
| ttage | 12 voltų |
| Vattage | 1.44 vatų |
| Dabartinė (A) | 0.13 A |
| Maitinimo jungties tipas | 4-Pin PWM |
| Guolio tipas | Dvigubas rutulinis guolis |
| MTBF (vidutinis laikas tarp gedimų) | 100,000 hours @ 35°C / 60,000 hours @ 60°C |
| Medžiaga | Plastikiniai |
| Suderinami įrenginiai | Staliniai kompiuteriai |
| Gamintojas | Nidec |
| UPC | 840556103585, 840556104087 |
Fiziniai matmenys:
Detailed dimensions for mounting and integration:
- Fan Frame: 119mm x 119mm (approx. 4.72 inches)
- Mounting Hole Spacing: 104.8mm x 104.8mm (center-to-center)
- Tvirtinimo angos skersmuo: 4.5 mm
- Fan Thickness: 25mm (0.98 inches)
- Cable Length: Approximately 300mm (11.8 inches)
