WaterCop Wireless Flood Sensor (WCDFS1) Instruction Manual

1. Įvadas

The WaterCop Wireless Flood Sensor (WCDFS1) is designed to detect the presence of water and transmit a wireless signal to a compatible WaterCop automatic water shut-off system. This system helps prevent water damage by automatically activating the shut-off valve when a leak is detected.

This sensor operates wirelessly, providing flexible placement options up to 200 feet from the main WaterCop system. It is powered by standard AA alkaline batteries.

2. Pakuotės turinys

• WaterCop Wireless Flood Sensor (WCDFS1)
• Remote Probe with cable
• Montavimo įranga (varžtai, inkarai)
• Šis naudojimo vadovas

3. Saugos informacija

• Prieš montuodami ir naudodami perskaitykite visas instrukcijas.
• Do not expose the sensor to extreme temperatures or direct sunlight.
• Ensure batteries are installed correctly according to polarity markings.
• Replace batteries annually or when indicated by the WaterCop system.
• Šis prietaisas skirtas naudoti tik patalpose.

4. Sąranka ir diegimas

4.1 Akumuliatoriaus įdėjimas

The WaterCop WCDFS1 sensor requires two (2) AA alkaline batteries (not included).

1. Atsargiai atidarykite jutiklį casing. Refer to the diagram for assistance.
2. Insert two AA alkaline batteries, observing the correct polarity (+/-) as marked inside the battery compartment.
3. Uždarykite jutiklį casing saugiai.

A pair of standard AA alkaline batteries should operate the sensor for approximately one year.

4.2 Jutiklio išdėstymas

Place the sensor in areas prone to water leaks, such as near water heaters, washing machines, dishwashers, sinks, toilets, or in basements.

The sensor transmits a wireless signal up to 200 feet to the WaterCop control unit. Consider potential obstructions like thick walls or metal objects that may reduce signal range.

The remote probe should be positioned directly on the floor or surface where water accumulation is most likely to occur.

4.3 Pairing with WaterCop System

The WCDFS1 sensor is compatible with all WaterCop systems. Refer to your specific WaterCop control unit's manual for detailed instructions on how to pair new sensors. Generally, this involves placing the control unit into a "learn" mode and then activating the sensor.

4.4 Montavimas

The sensor unit can be wall-mounted using the provided hardware. Ensure the remote probe cable reaches the desired detection area.

5. Operacija

Once installed and paired, the WaterCop Wireless Flood Sensor continuously monitors for the presence of water at its remote probe.

Upon detecting water, the sensor immediately transmits a wireless signal to the WaterCop control unit.

The WaterCop control unit, upon receiving this signal, will activate the automatic shut-off valve, thereby stopping the water supply to prevent further damage.

The sensor will continue to transmit the alarm signal until the water is no longer detected by the probe.

6. Priežiūra

6.1 Akumuliatoriaus keitimas

Replace the AA alkaline batteries annually or when the WaterCop control unit indicates a low battery signal from the sensor.

1. Atidarykite jutiklį casing.
2. Išimkite senas baterijas ir atsakingai jas išmeskite.
3. Įdėkite dvi naujas AA šarmines baterijas, užtikrindami teisingą poliškumą.
4. Uždarykite jutiklį casing saugiai.

6.2 Valymas

Periodically inspect the sensor and probe for dust or debris. Clean with a soft, dry cloth. Do not use abrasive cleaners or immerse the unit in water.

6.3 Testavimas

It is recommended to test the sensor's functionality periodically (e.g., every 3-6 months).

1. Place a small amount of water (e.g., a few drops) on the remote probe.
2. Observe if the WaterCop control unit receives the alarm signal and activates the shut-off valve.
3. Remove the water from the probe and verify that the WaterCop system resets or allows manual reset.
4. Refer to your WaterCop control unit's manual for specific testing procedures.

7. Problemų sprendimas

7.1 Sensor not detecting water:

• Ensure the remote probe is making good contact with the surface.
• Patikrinkite akumuliatoriaus lygį ir, jei reikia, pakeiskite.
• Verify the sensor is correctly paired with the WaterCop control unit.

7.2 WaterCop system not responding to sensor:

• Check the sensor's batteries.
• Ensure the sensor is within the 200 ft wireless range of the WaterCop control unit and there are no significant obstructions.
• Re-pair the sensor with the WaterCop control unit.
• Consult the WaterCop control unit's manual for troubleshooting its reception.

7.3 False alarms:

• Ensure the probe is not placed in an area where condensation or minor spills are common and not indicative of a leak.
• Check for any moisture on the probe that might be causing a false trigger.

8. Specifikacijos

9. Garantija ir palaikymas

For warranty information and technical support, please refer to the official WaterCop websvetainėje arba susisiekite tiesiogiai su jų klientų aptarnavimo tarnyba. Išsaugokite pirkimo kvitą garantiniams reikalavimams.

Official WaterCop Websvetainė: www.watercop.com

Contact Information: Refer to the websvetainė, kurioje pateikiami naujausi kontaktiniai duomenys.