Fengda AS18B Airbrush Compressor Instruction Manual

1. Įvadas

This manual provides essential information for the safe and efficient operation, setup, and maintenance of your Fengda AS18B Airbrush Compressor. Please read these instructions carefully before using the compressor to ensure proper function and longevity of the device.

2. Saugos instrukcijos

• Elektros sauga: Ensure the compressor is connected to a grounded power outlet with the correct voltage (230 V). Nenaudokite šlapiomis rankomis arba damp Prieš atlikdami bet kokią techninę priežiūrą, atjunkite maitinimą.
• Vėdinimas: Operate the compressor in a well-ventilated area to prevent overheating. Do not block air vents.
• Slėgis: Never exceed the maximum operating pressure of the compressor or the connected airbrush. Always release pressure from the system before disconnecting hoses or performing maintenance.
• Vaikai ir augintiniai: Kompresorių laikykite vaikams ir naminiams gyvūnams nepasiekiamoje vietoje. Tai ne žaislas.
• Numatytas naudojimas: Use the compressor only for its intended purpose of supplying compressed air for airbrushing. Do not modify the unit.

3. Produktas baigtasview

The Fengda AS18B is a compact, oil-free piston airbrush compressor designed for quiet and consistent air delivery. It features an integrated manometer, pressure regulator, and an automatic start/stop function.

Image 1: Fengda AS18B Airbrush Compressor. This image displays the main compressor unit, including the attached pressure regulator and water filter on the left side, and the carrying handle on top. The unit is silver-colored with black accents.

Pagrindiniai komponentai:

• Kompresoriaus blokas: The main body housing the motor and piston.
• Slėgio reguliatorius: Leidžia reguliuoti išėjimo oro slėgį.
• Manometras (slėgio matuoklis): Displays the current output air pressure.
• Vandens filtras: Removes moisture from the air, preventing condensation in your airbrush.
• Oro išleidimo anga: 1/8 inch (9.51 mm) connection for airbrush hose.
• Nešiojimo rankena: Kad būtų lengviau pernešti.

4. Sąranka

1. Išpakavimas: Carefully remove the compressor from its packaging. Inspect for any damage.
2. Vieta: Place the compressor on a stable, level surface in a well-ventilated area. Ensure adequate space around the unit for air circulation.
3. Connect Airbrush Hose: Connect one end of your airbrush hose to the 1/8 inch air outlet on the pressure regulator. Connect the other end to your airbrush. Ensure all connections are secure to prevent air leaks.
4. Maitinimo jungtis: Plug the power cord into a suitable 230V grounded electrical outlet.

5. Naudojimo instrukcijos

1. Maitinimas: Turn on the compressor using the power switch. The compressor will start running and build pressure.
2. Sureguliuokite slėgį: The manometer will display the current output pressure. To adjust the pressure, turn the knob on the pressure regulator. Turn clockwise to increase pressure and counter-clockwise to decrease pressure.
3. Automatinis paleidimas / sustabdymas: The AS18B features an automatic start/stop function. The compressor will automatically start when the pressure drops below approximately 3 bar and stop when it reaches approximately 4 bar. This maintains a consistent working pressure and reduces wear.
4. Begin Airbrushing: Once the desired pressure is set, you can begin using your airbrush.
5. Išjungti: After use, turn off the compressor using the power switch and disconnect it from the power outlet.

6. Priežiūra

• Drain Water Filter: Regularly check the water filter for accumulated moisture. To drain, ensure the compressor is off and depressurize the system. Unscrew the drain valve at the bottom of the water filter to release collected water. Re-tighten the valve securely.
• Valymas: Wipe the exterior of the compressor with a clean, damp cloth. Do not use harsh chemicals or abrasive cleaners. Ensure air vents are free from dust and debris.
• Saugykla: Store the compressor in a clean, dry place away from direct sunlight and extreme temperatures.

7. Problemų sprendimas

• Kompresorius neįsijungia:
  • Patikrinkite, ar maitinimo laidas tvirtai prijungtas.
  • Įsitikinkite, kad maitinimo jungiklis yra „ĮJUNGTA“ padėtyje.
  • Verify the electrical outlet is functioning.
• No air output or low pressure:
  • Check all hose connections for leaks. Tighten if necessary.
  • Ensure the pressure regulator knob is adjusted correctly (clockwise to increase pressure).
  • Check if the airbrush nozzle is clogged. Clean the airbrush if needed.
  • Verify the water filter is not excessively full, which can restrict airflow.
• Compressor runs continuously:
  • This may indicate an air leak in the system (hose, airbrush connection). Check all connections.
  • If no leaks are found, the automatic shut-off mechanism may require inspection by a qualified technician.

8. Specifikacijos

9. Garantija ir palaikymas

Dėl garantijos informacijos ar techninės pagalbos žr. kartu su pirkiniu pateiktus dokumentus arba susisiekite tiesiogiai su gamintoju. Išsaugokite pirkimo įrodymą, jei galėtumėte pateikti garantijos pretenzijas.