PEDROLLO 2CPm 25/16B Electric Centrifugal Pump User Manual

1. Įvadas

This manual provides essential information for the safe and efficient operation, installation, and maintenance of your PEDROLLO 2CPm 25/16B Electric Centrifugal Pump. Please read this manual thoroughly before operating the pump to ensure proper use and to prevent damage or injury.

Figure 1: PEDROLLO 2CPm 25/16B Electric Centrifugal Pump. This image shows the complete pump unit, featuring the blue pump body connected to the electric motor, designed for efficient fluid transfer.

2. Saugos informacija

Visada laikykitės šių saugos priemonių, kad sumažintumėte sužalojimo, elektros smūgio, gaisro ar siurblio sugadinimo riziką.

• Elektros sauga: Ensure the pump is connected to a properly grounded power supply. Do not operate with damaged cords or plugs. Disconnect power before any maintenance or service.
• Vandens sauga: Do not operate the pump dry. Ensure the pump is always primed before starting. Protect the pump from freezing temperatures.
• Montavimas: Install the pump on a stable, level surface. Ensure adequate ventilation around the motor. Use appropriate pipe fittings and sealants to prevent leaks.
• Asmeninės apsaugos priemonės (AAP): Wear appropriate safety gear, such as gloves and eye protection, when handling the pump or performing maintenance.
• Vaikai ir augintiniai: Veikiant siurbliui, laikykite vaikus ir naminius gyvūnus atokiau nuo jo.

3. Product Components and Description

The PEDROLLO 2CPm 25/16B is a single-phase electric centrifugal pump designed for efficient water transfer. It features a cast iron pump body and a stainless steel crankshaft, ensuring durability and reliable performance.

• Galia: 2 AG (1.5 kW)
• Maksimalus srautas: 140 liters/minute (200 l/min)
• Maksimali galva: 56 metrų
• Maksimalus siurbimo pakėlimas: 7 metrų
• Suction Nozzle Diameter: 1 1/4 colio
• Discharge Nozzle Diameter: 1 colio

Figure 2: Internal Diagram of the Centrifugal Pump. This diagram illustrates the key internal components of the pump, showing the flow path and mechanical parts.

• 1. Pump Casing: The outer housing of the pump, typically made of cast iron, which contains the impeller and directs the fluid flow.
• 2. Discharge Port: The outlet through which the pumped fluid exits the pump.
• 3. Impeller: The rotating component with vanes that imparts kinetic energy to the fluid, increasing its velocity and pressure.
• 4. Motor Shaft: The rotating shaft that connects the motor to the impeller, transmitting power.
• 5. Mechanical Seal: Prevents fluid leakage along the motor shaft where it enters the pump casing.
• 6. Bearings: Support the rotating shaft, reducing friction and ensuring smooth operation.
• 7. Motor Stator: The stationary part of the electric motor that contains the windings, generating the magnetic field.
• 8. Motor Rotor: The rotating part of the electric motor, connected to the shaft, which interacts with the stator's magnetic field to produce torque.

4. Sąranka ir diegimas

4.1 Išpakavimas ir patikrinimas

1. Atsargiai išimkite siurblį iš pakuotės.
2. Inspect the pump for any visible damage that may have occurred during shipping. Report any damage to your supplier immediately.
3. Įsitikinkite, kad yra visi pakavimo sąraše išvardyti komponentai.

4.2 Siurblio montavimas

1. Select a dry, well-ventilated location, protected from direct sunlight and freezing temperatures.
2. Mount the pump on a solid, level foundation to minimize vibration and noise. Use appropriate bolts to secure the pump through its base plate holes.
3. Įsitikinkite, kad aplink siurblį yra pakankamai vietos ventiliacijai ir būsimai techninei priežiūrai.

4.3 Santechnikos jungtys

1. Connect the suction pipe to the pump's inlet (1 1/4 inch) and the discharge pipe to the outlet (1 inch).
2. Use appropriate pipe thread sealant on all connections to prevent leaks.
3. Ensure that the piping is adequately supported to prevent strain on the pump connections.
4. Install a foot valve with a strainer at the end of the suction pipe if drawing water from a well or tank.

4.4 Elektros prijungimas

1. Įsitikinkite, kad maitinimo šaltinis atitinka siurblio įtampątage reikalavimai (230 V kintamoji srovė).
2. Connect the pump to a dedicated, properly grounded electrical circuit protected by a circuit breaker or fuse.
3. All electrical wiring should be performed by a qualified electrician in accordance with local electrical codes.

5. Operacija

5.1 Siurblio užpildymas

Before initial start-up or after the pump has been drained, it must be primed.

1. Remove the priming plug (if present) or open a valve on the discharge side.
2. Užpildykite siurblį casing completely with water until it overflows.
3. Replace the priming plug or close the valve.

5.2 Siurblio paleidimas

1. Įsitikinkite, kad siurblys tinkamai užpildytas.
2. Open any necessary valves on the suction and discharge lines.
3. Turn on the power supply to the pump. The pump should start immediately.
4. Monitor the pump for unusual noises or vibrations during the first few minutes of operation.

5.3 Siurblio išjungimas

1. Išjunkite siurblio maitinimą.
2. Close any necessary valves on the suction and discharge lines to prevent backflow.

6. Priežiūra

Reguliarus siurblio aptarnavimas užtikrina jo ilgaamžiškumą ir optimalų veikimą.

6.1 Routine Checks (Weekly/Monthly)

• Check for any leaks around the pump casing or pipe connections.
• Listen for unusual noises or vibrations during operation.
• Patikrinkite, ar maitinimo laidas nepažeistas.
• Ensure the pump is adequately ventilated and free from debris.

6.2 Valymas

• Periodically clean the exterior of the pump to prevent dirt buildup.
• If the pump is used with dirty water, regularly check and clean the strainer on the suction line.

6.3 Žiemos paruošimas / sandėliavimas

• If the pump will not be used for an extended period or in freezing temperatures, drain all water from the pump casing and pipes to prevent damage from ice expansion.
• Siurblį laikykite sausoje, apsaugotoje vietoje.

7. Problemų sprendimas

Dažniausiai pasitaikančias problemas ir galimus jų sprendimus žr. toliau pateiktoje lentelėje.

8. Techninės specifikacijos

Detailed specifications for the PEDROLLO 2CPm 25/16B Electric Centrifugal Pump.

9. Garantija ir palaikymas

For product support, technical assistance, or warranty inquiries, please contact your authorized PEDROLLO dealer or the point of purchase. While specific warranty terms may vary by region and retailer, general return policies often allow for refund or replacement within 30 days of purchase, subject to the seller's terms and conditions.

Always refer to your purchase documentation for specific warranty details applicable to your product.

Gamintojas: PEDROLLO

For further assistance, you may visit the official PEDROLLO websvetainėje arba susisiekite su klientų aptarnavimo skyriumi.