1. Įvadas
Thank you for choosing the CREWORKS Electric PCP Air Compressor Pump. This manual provides essential information for the safe and efficient operation, setup, and maintenance of your compressor. Please read this manual thoroughly before using the product and retain it for future reference.
This portable electric air compressor is designed to produce high pressures up to 4500 PSI (30 MPa / 300 BAR), featuring an adjustable auto-stop function for precise pressure control. It is suitable for various applications including filling PCP air rifles, paintball tanks, airsoft equipment, and for pressure leakage testing.
2. Saugos instrukcijos
ĮSPĖJIMAS: Failure to follow these safety instructions may result in serious injury, property damage, or death.
- Aušinimo sistema: ALWAYS ensure the water cooling system is properly set up and functioning before starting the compressor. An external bucket of cooling water is required. NEVER operate the machine without adequate cooling water. Monitor the digital thermometer to prevent overheating.
- Aukštas slėgis: This compressor generates extremely high pressure. Always wear appropriate eye protection and ensure all connections are secure before operation. Never point the air outlet at yourself or others.
- Elektros sauga: Connect the compressor to a standard 110V 60Hz single-phase grounded outlet. Do not operate with damaged cords or plugs. Keep the compressor away from water and damp aplinkos.
- Vėdinimas: Kompresorių naudokite gerai vėdinamoje patalpoje, kad išvengtumėte perkaitimo ir užtikrintumėte tinkamą oro įsiurbimą.
- Vaikai ir augintiniai: Kompresoriui veikiant, laikykite vaikus ir naminius gyvūnus atokiau nuo jo.
- Priežiūra: Perform maintenance only when the compressor is unplugged and depressurized. Refer to the maintenance section for proper procedures.
- Alyvos lygis: Regularly check the oil level. Refill immediately if the level is low, using ISO VG46 or AW 46 lubricating oil.
3. Gaminio komponentai
Familiarize yourself with the main components of your CREWORKS Electric PCP Air Compressor Pump:
4. Sąranka
Follow these steps for initial setup before operating the compressor:
- Išpakavimas ir patikrinimas: Carefully remove the compressor from its packaging. Inspect for any visible damage during transit. Ensure all accessories (air hose, nozzles) are present.
- Aušinimo sistemos prijungimas:
- Place an external bucket of clean water near the compressor.
- Connect the water inlet hose to the compressor's water inlet port and submerge the other end into the bucket.
- Connect the water outlet hose to the compressor's water outlet port and submerge the other end into the bucket, ensuring proper circulation.
- Ensure the water pump (if external) is ready for operation or that the self-contained cooling system is filled and ready.
- Patikrinkite alyvos lygį: Locate the oil level sight glass (refer to Figure 3.2). The oil level should be between the minimum and maximum marks. If low, add ISO VG46 or AW 46 lubricating oil through the respirator (refueling hole) until the correct level is reached.
- Prijunkite oro žarną: Attach the 8mm air hose connector with the quick-connect fitting to the desired tank or device you intend to fill. Ensure a secure, leak-free connection.
- Maitinimo jungtis: Plug the compressor's power cord into a standard 110V 60Hz grounded electrical outlet.
5. Naudojimo instrukcijos
Once setup is complete, follow these steps to operate your compressor:
- Nustatykite pageidaujamą slėgį: Rotate the knob on the adjustable pressure gauge (Figure 3.4) to set your target pressure. The compressor will automatically stop when this pressure is reached. The maximum pre-set pressure is 30 MPa (4500 PSI).
- Start Cooling System: If using an external water pump, activate it to ensure water circulation. If the system is self-contained, ensure it is ready.
- Kompresoriaus paleidimas: Flip the power switch to the 'ON' position. The compressor will begin to fill the connected tank.
- Monitoriaus veikimas:
- Continuously monitor the pressure gauge to observe the filling progress.
- Observe the digital thermometer to ensure the compressor's temperature remains within safe operating limits. If the temperature rises too high, stop the compressor immediately and allow it to cool.
- Listen for any unusual noises or signs of leakage.
- Automatinio sustabdymo funkcija: The compressor will automatically shut off once the pre-set pressure is achieved.
- Išjungti:
- Turn off the compressor power switch.
- Depressurize the system by slowly opening the pressure relief screw.
- Disconnect the air hose from the tank.
- Turn off the cooling system.
6. Priežiūra
Reguliarus kompresoriaus aptarnavimas užtikrina jo ilgaamžiškumą ir optimalų veikimą.
- Oil Change/Refill: Check the oil level before each use. Change the oil every 20-30 hours of operation or every 3 months, whichever comes first. Use ISO VG46 or AW 46 lubricating oil. To change, drain old oil from the oil outlet and refill through the respirator.
- Aušinimo vanduo: Replace cooling water regularly, especially if it appears dirty or discolored. Ensure the cooling system is free from blockages.
- Valymas: Keep the exterior of the compressor clean and free of dust and debris. Use a dry cloth. Do not use harsh chemicals or solvents.
- Oro filtras: Inspect and clean or replace the air filter as needed to ensure clean air intake.
- Saugykla: When not in use, store the compressor in a dry, cool place, away from direct sunlight and moisture.
7. Problemų sprendimas
Dažniausiai pasitaikančias problemas ir jų sprendimus rasite šiame skyriuje.
| Problema | Galima priežastis | Sprendimas |
|---|---|---|
| Kompresorius neįsijungia | Nėra maitinimo; Maitinimo jungiklis išjungtas; Suaktyvintas šiluminis perkrovimas | Check power connection; Turn on power switch; Allow compressor to cool down and reset. |
| Kompresorius perkaista | Insufficient cooling water; Blocked water circulation; Prolonged operation | Ensure adequate cooling water and circulation; Check for blockages; Allow compressor to cool; Do not operate continuously for extended periods. |
| Not reaching desired pressure | Air leak in connections; Pressure gauge setting too low; Worn piston rings | Check all hose connections for leaks; Adjust pressure gauge setting; Contact customer support for service. |
| Per didelis triukšmas ar vibracija | Loose components; Insufficient oil; Unit not on a stable surface | Inspect and tighten all fasteners; Check and refill oil; Place compressor on a firm, level surface. |
8. Specifikacijos
Key technical specifications for the CREWORKS Electric PCP Air Compressor Pump (Model SX-HPA3LSPUS):
| Funkcija | Specifikacija |
|---|---|
| Prekės ženklas | ĮRENGINIAI |
| Modelio numeris | SX-HPA3LSPUS |
| ttage | 110 voltų |
| Maitinimo šaltinis | Su laidu elektra |
| Galia | 1.80 kW |
| Maksimalus slėgis | 4500 PSI / 30 MPa / 300 BAR |
| Darbingumas | 50 l/min |
| Įkrovimo norma | 40-50 L/min (1.5 - 1.8 CFM) |
| Triukšmo lygis | Mažiau nei 78 dB |
| Tepimo alyva | ISO VG46 or AW 46 |
| Prekės svoris | 45.6 svaro (apie 18 kg) |
| Pakuotės matmenys | 19 x 18.5 x 12 colio |
| Ypatinga funkcija | Adjustable Control with Auto-Stop |
| Įtraukti komponentai | Oro žarna, purkštukai |
9. Garantija ir palaikymas
This CREWORKS Electric PCP Air Compressor Pump comes with a 1 metų garantija nuo įsigijimo datos, apimanti gamybos defektus.
For technical support, warranty claims, or replacement parts, please contact CREWORKS customer service. Please have your model number (SX-HPA3LSPUS) and purchase information ready when contacting support.
Kontaktinė informacija:
Please refer to the contact details provided with your product packaging or visit the official CREWORKS websvetainę, kurioje rasite naujausią pagalbos informaciją.