Axxess AXLOC-FD2 2-Channel Line Output Converter Instruction Manual for Ford 2011-Up

Įvadas

The Axxess AXLOC-FD2 is a 2-channel line output converter designed to integrate aftermarket amplifiers with factory audio systems in select Ford vehicles from 2011 and newer. This device converts high-level speaker signals from the factory radio into low-level RCA signals, providing a clean and adjustable output for your amplifier. It also provides a 12-volt accessory output for ampkeltuvo įjungimas.

Saugos informacija

• Prieš pradėdami bet kokį montavimą, visada atjunkite neigiamą automobilio akumuliatoriaus gnybtą.
• Įsitikinkite, kad visi laidų sujungimai yra tvirti ir tinkamai izoliuoti, kad išvengtumėte trumpojo jungimo.
• Jei nesate tikri dėl kurios nors montavimo proceso dalies, kreipkitės į profesionalų automobilių garso sistemų montuotoją.
• Do not operate the vehicle's audio system at excessively high volumes for prolonged periods, as this may cause hearing damage.
• Mount the converter in a location that is protected from moisture and excessive heat.

Pakuotės turinys

Prieš pradėdami diegti, patikrinkite, ar yra visi elementai:

• AXLOC-FD2 Line Output Converter Module
• Vehicle-specific wiring harness
• RCA output cables
• Remote turn-on wire

Montavimo instrukcijos

This section outlines the general installation procedure. Specific vehicle disassembly instructions are beyond the scope of this manual. Refer to a vehicle-specific service manual for dash removal and access to the factory radio wiring.

Reikalingi įrankiai:

• Vielos nuėmikliai/grybeliukai
• Elektros juosta arba susitraukiantis vamzdelis
• Multimetras
• Plokščių nuėmimo įrankiai
• Screwdrivers/socket set

Laidų schema ir jungtys:

1. Atjunkite akumuliatorių: Before starting, disconnect the negative terminal of the vehicle's battery to prevent electrical shorts.
2. Access Factory Radio: Carefully remove the necessary trim panels and components to gain access to the back of the factory radio.
3. Garsiakalbių laidų identifikavimas: Using a vehicle-specific wiring diagram or a multimeter, identify the factory speaker output wires (positive and negative for each channel) from the factory radio harness.
4. Connect Input Harness: Connect the vehicle-specific wiring harness provided with the AXLOC-FD2 to the factory radio harness. This harness will typically plug in-line with the factory radio, intercepting the speaker outputs.
5. Connect AXLOC-FD2 Module: Plug the main connector from the vehicle-specific harness into the AXLOC-FD2 module.
6. Prijunkite RCA išėjimus: Connect the RCA output cables from the AXLOC-FD2 module to the RCA inputs of your aftermarket ampgyvesnis.
7. Connect Remote Turn-On: The AXLOC-FD2 provides a 12-volt accessory output (remote turn-on) for your amplifier. Connect this wire to the remote turn-on input of your amplifier. This eliminates the need to find a separate switched 12V source.
8. Įžeminimo jungtis: Ensure the AXLOC-FD2 module has a solid ground connection. The vehicle-specific harness should provide this, but always verify.
9. Montavimas: Securely mount the AXLOC-FD2 module in a suitable location, away from heat and moisture, ensuring it does not interfere with any moving parts or vehicle components.

Naudojimo instrukcijos

Stiprinimo reguliavimas:

The AXLOC-FD2 features adjustable gain controls to match the output level of the factory radio to the input sensitivity of your aftermarket amplifier. Proper gain setting is crucial for optimal sound quality and to prevent distortion.

1. Pradinis nustatymas: Start with the gain controls on the AXLOC-FD2 set to their minimum position (fully counter-clockwise).
2. Amppadidinimo prieaugis: Set the gain control on your aftermarket amplifier to its minimum position.
3. Groti muziką: Play a dynamic piece of music through your factory radio at about 75% of its maximum volume.
4. Adjust AXLOC-FD2 Gain: Slowly increase the gain controls on the AXLOC-FD2 until you hear a slight distortion, then back off slightly until the sound is clean.
5. Sureguliuoti Amppadidinimo prieaugis: Once the AXLOC-FD2 gain is set, slowly increase the gain control on your amplifier until the desired volume is achieved without distortion.
6. Tikslus derinimas: Make small adjustments to both the AXLOC-FD2 and amplifier gains as needed to achieve the best sound quality. Avoid setting gains too high, as this will introduce distortion and can damage speakers.

Priežiūra

The Axxess AXLOC-FD2 is designed for reliable, maintenance-free operation. No user-serviceable parts are inside. To ensure longevity:

• Laikykite įrenginį švarų nuo dulkių ir šiukšlių.
• Ensure all wiring connections remain secure.
• Saugokite, kad įrenginys nepatektų į ekstremalią temperatūrą ar drėgmę.

Trikčių šalinimas

Specifikacijos

• Modelis: AXLOC-FD2
• Kanalai: 2 kanalas
• Įvesties tipas: High-level (speaker level)
• Išvesties tipas: Low-level (RCA)
• Suderinamumas: Ford vehicles 2011-Up
• Savybės: Adjustable gain, 12V remote turn-on output
• Prekės svoris: Maždaug 1.37 svaro
• Pakuotės matmenys: Maždaug 10.39 x 10.31 x 4.92 colio

Garantija ir palaikymas

Dėl garantijos informacijos ar techninės pagalbos kreipkitės į oficialią gamintojo svetainę. websvetainėje arba susisiekite su jų klientų aptarnavimo skyriumi. Išsaugokite pirkimo įrodymą garantiniams reikalavimams.

Gamintojas: Axxess

Websvetainė: axxessinterfaces.com (Pvzampnuoroda, tikroji nuoroda gali skirtis)