Total TG5411611 Gasoline Chainsaw User Manual

Įvadas

This manual provides essential instructions for the safe operation, maintenance, and troubleshooting of your Total TG5411611 Gasoline Chainsaw. Please read this manual thoroughly before operating the chainsaw to ensure proper use and to prevent injury or damage. Keep this manual in a safe place for future reference.

The Total TG5411611 is a powerful 2-stroke gasoline chainsaw designed for various cutting tasks. It features a 41cc engine with 2 HP, a 40 cm (16-inch) cutting bar, and is capable of cutting materials up to 405 mm in diameter. It has a fuel tank capacity of 260 ml and an oil tank capacity of 210 ml.

Image 1: Total TG5411611 Gasoline Chainsaw. This image displays the overall appearance of the chainsaw, including the engine housing, handle, and cutting bar with chain.

Svarbūs saugos įspėjimai

• Always wear appropriate personal protective equipment (PPE) including a helmet, eye protection, hearing protection, gloves, and safety boots when operating the chainsaw.
• Užtikrinkite, kad darbo zonoje nebūtų pašalinių asmenų, vaikų ir naminių gyvūnėlių.
• Do not operate the chainsaw when fatigued, under the influence of alcohol, drugs, or medication.
• Inspect the chainsaw before each use for loose parts, damage, or wear. Do not operate a damaged chainsaw.
• Handle fuel with extreme care. Refuel in a well-ventilated area with the engine off and cool. Avoid spilling fuel.
• Darbo metu tvirtai laikykite grandininio pjūklo rankenas abiem rankomis.
• Saugokitės atatrankos. Venkite pjauti kreipiamosios juostos galu.
• Never operate the chainsaw indoors or in poorly ventilated areas due to exhaust fumes.

Sąranka ir surinkimas

1. Išpakavimas

Carefully remove all components from the packaging. Verify that all parts listed in the packing list are present and undamaged. Retain packaging materials for future storage or transport.

2. Kreipiamosios juostos ir grandinės montavimas

1. Įsitikinkite, kad variklis išjungtas ir grandinės stabdys įjungtas.
2. Nuimkite grandinės dangtelį, atlaisvindami dvi veržles.
3. Place the guide bar onto the studs, ensuring the chain tension pin aligns with the hole in the guide bar.
4. Carefully fit the chain around the clutch drum and into the groove of the guide bar. Ensure the cutting edges of the chain are facing forward in the direction of rotation.
5. Uždėkite grandinės dangtelį ir ranka priveržkite veržles. Dar iki galo neužveržkite.

3. Grandinės įtempimo reguliavimas

1. Using the chain tensioning screw (usually located on the side of the chainsaw), adjust the chain tension.
2. The chain should be snug against the guide bar, but still able to be pulled freely by hand. There should be no slack on the underside of the bar, and the drive links should be seated in the bar groove.
3. Once the tension is correct, fully tighten the two nuts on the chain cover.
4. Re-check chain tension after tightening the nuts.

4. Fuel and Chain Oil Filling

Svarbu: This chainsaw uses a 2-stroke engine. It requires a mixture of gasoline and 2-stroke engine oil. Refer to the engine oil manufacturer's instructions for the correct mixing ratio (typically 25:1 or 50:1, depending on the oil type). Use unleaded gasoline with an octane rating of 90 or higher.

1. Įsitikinkite, kad variklis išjungtas ir atvėsęs.
2. Locate the fuel tank cap (usually marked with a fuel pump icon) and the chain oil tank cap (usually marked with an oil drop icon).
3. Carefully fill the fuel tank with the correct gasoline/oil mixture (capacity: 260 ml).
4. Fill the chain oil tank with high-quality chain lubricant (capacity: 210 ml). This oil lubricates the chain and guide bar during operation.
5. Securely replace both caps. Wipe up any spills immediately.

Naudojimo instrukcijos

1. Variklio užvedimas

1. Padėkite grandininį pjūklą ant tvirto, lygaus paviršiaus. Įsitikinkite, kad grandinės stabdys įjungtas.
2. ĮJUNGIMO/IŠJUNGIMO jungiklį nustatykite į „ĮJUNGTA“ padėtį.
3. Pull the choke lever out (for cold start).
4. Kelis kartus paspauskite degalų pildymo lemputę, kol grįžtamojoje linijoje pamatysite degalų.
5. Tvirtai laikykite grandininį pjūklą viena ranka už priekinės rankenos, o koją uždėkite ant galinės rankenos.
6. Pull the starter cord briskly until the engine fires (usually a few pulls).
7. Once the engine fires, push the choke lever in halfway (if applicable) or fully in.
8. Dar kartą traukite starterio virvę, kol variklis užsives ir veiks sklandžiai.
9. Allow the engine to warm up for a few moments before disengaging the chain brake and beginning work.

2. Pagrindiniai pjovimo būdai

• Visada išlaikykite pusiausvyrą ir tvirtai laikykite grandininį pjūklą.
• Plan your cuts to avoid kickback and ensure the wood falls in a safe direction.
• Start cutting with the bottom of the guide bar, using the bumper spike as a pivot point.
• Venkite pjauti kreipiamosios juostos galu, nes tai padidina atatrankos riziką.
• Do not force the chainsaw through the wood; let the chain do the work.
• Be aware of pinching. Use wedges if necessary to prevent the guide bar from getting stuck.

3. Variklio išjungimas

To stop the engine, simply move the ON/OFF switch to the "OFF" position. Engage the chain brake immediately after stopping the engine.

Priežiūra

Regular maintenance is crucial for the safe and efficient operation of your chainsaw. Always ensure the engine is off and cool, and the spark plug cap is disconnected before performing any maintenance.

1. Grandinės galandimas

• Aštri grandinė yra būtina saugiam ir efektyviam pjovimui. Reguliariai galąskite grandinę arba pakeiskite ją, kai ji atšipsta.
• Naudokite apvalią file tinkamo skersmens jūsų grandinei (žr. grandinės specifikacijas).
• File each cutter with consistent strokes, maintaining the correct angle.
• Patikrinkite ir file the depth gauges as needed.

2. Oro filtro valymas

Clean the air filter frequently, especially when working in dusty conditions. A clogged air filter can reduce engine performance and increase fuel consumption.

1. Nuimkite oro filtro dangtelį.
2. Nuimkite oro filtro elementą.
3. Clean the filter with warm, soapy water, or compressed air. Allow it to dry completely before reinstallation.

3. Uždegimo žvakių patikra

Inspect the spark plug periodically for wear, carbon buildup, or damage. Clean or replace as necessary to ensure reliable starting and engine performance.

4. Kreipiamosios juostos priežiūra

• Reguliariai valykite kreipiamosios juostos griovelį, kad pašalintumėte pjuvenas ir šiukšles.
• Check the guide bar for burrs or wear. File down any burrs.
• Periodiškai apverskite kreipiamąją juostą, kad užtikrintumėte tolygų nusidėvėjimą.

5. Sandėliavimas

When storing the chainsaw for an extended period, drain the fuel tank or run the engine until it runs out of fuel. Clean the chainsaw thoroughly and store it in a dry, secure location away from children.

Trikčių šalinimas

Dėl čia neaptartų problemų kreipkitės į įgaliotąjį techninės priežiūros centrą.

Specifikacijos

Garantija ir palaikymas

For warranty information, technical support, or to locate an authorized service center, please refer to the warranty card included with your product or visit the official Total Tools websvetainėje. Išsaugokite pirkimo kvitą kaip pirkimo įrodymą garantiniams reikalavimams.

Gamintojas: Iš viso

Modelis: TG5411611