UNI-T UT693A-C01 Multifunction Fiber Optic Power Meter Instruction Manual

1. Įvadas

The UNI-T UT693A-C01 is a versatile 4-in-1 handheld device designed for fiber optic and network cable testing. It integrates an optical power meter, a visual fault locator (VFL), an RJ45 network cable sequence tester, and an LED flashlight into a single compact unit. This manual provides essential information for the safe and efficient operation of your UT693A-C01.

Pagrindinės funkcijos:

• Optinis galios matuoklis: Wide C-Type measurement range (-50~+30dBm) with 10 calibration wavelengths (850nm to 1650nm).
• Vizualinis gedimų lokatorius (VFL): Powerful 30mW red light (650nm) with dual modes for identifying fiber breaks, bends, and faulty connectors.
• RJ45 Network Cable Tester: Built-in port for testing network cable wire order and verifying signal transmission integrity.
• LED žibintuvėlis: Integrated LED for illuminating work areas.
• Duomenų registravimas: Stores up to 500 measurement records for review ir analizė.
• C tipo įkrovimas: Convenient USB Type-C interface for recharging the internal battery.

2. Saugos informacija

Please read and understand all safety warnings and operating instructions before using this device. Failure to follow these instructions may result in injury or damage to the device.

2.1 Laser Safety Warning

The UT693A-C01 contains a Visual Fault Locator (VFL) that emits a 650nm red laser. This is a Class IIIA laser product. Direct exposure to the laser beam can cause eye damage.

• ĮSPĖJIMAS: Laser radiation. Do not look directly into the beam. Avoid close contact.
• Never look directly into the optical output port when the VFL is active.
• Do not point the laser at people or animals.
• Use caution when working with fiber optic cables, as broken fibers can be sharp.

2.2 Bendrosios saugos priemonės

• Nebandykite ardyti ar modifikuoti įrenginio. Visus techninės priežiūros darbus patikėkite kvalifikuotiems darbuotojams.
• Saugokite įrenginį nuo vandens, drėgmės ir ekstremalių temperatūrų.
• Naudokite tik nurodytą įkrovimo laidą ir maitinimo adapterį.
• Prietaisą valykite minkštu, sausu skudurėliu. Nenaudokite abrazyvinių valiklių ar tirpiklių.

Paveikslėlis: Nugara view of the UT693A-C01, displaying a laser warning symbol and basic specifications in Chinese, including model number, power measurement range, red light wavelength, output power, laser class, and battery type (3.7V 450mAh Lithium Battery).

3. Pakuotės turinys

Išpakuodami patikrinkite, ar pakuotėje yra visi reikalingi daiktai:

• UNI-T UT693A-C01 Main Unit
• C tipo įkrovimo laidas
• Vartotojo vadovas
• Garantijos kortelė (jei taikoma)

Image: The complete package contents for the UT693A-C01, showing the device, a Type-C charging cable, and printed user manual and card.

4. Įrenginys baigtasview ir Sąranka

4.1 Įrenginio išdėstymas

Vaizdas: priekis view of the UT693A-C01, highlighting the LCD display and the various function buttons for ON/OFF, VFL, Wavelength, Save, Set, and REF.

4.2 Įrenginio įkrovimas

The UT693A-C01 is equipped with a built-in 3.7V 450mAh lithium battery. Before initial use, fully charge the device.

1. Locate the Type-C charging port, typically covered by a protective cap.
2. Connect the provided Type-C charging cable to the device.
3. Connect the other end of the cable to a standard USB power adapter (5V/1A recommended) or a computer USB port.
4. The charging indicator on the device will show the charging status. Disconnect once fully charged.

Image: The UT693A-C01 connected to a USB power source via its Type-C port for charging, demonstrating its portability and built-in rechargeable battery.

4.3 Įjungimas / išjungimas

• Norėdami įjungti įrenginį, paspauskite ir palaikykite ĮJUNGTA/IŠJUNGTA mygtuką maždaug 2 sekundes.
• Norėdami išjungti įrenginį, paspauskite ir palaikykite ĮJUNGTA/IŠJUNGTA mygtuką maždaug 2 sekundes, kol ekranas išsijungs.

5. Naudojimo instrukcijos

5.1 Optical Power Measurement

The optical power meter function measures the power of optical signals in fiber optic networks.

1. Įsitikinkite, kad įrenginys įjungtas.
2. Connect the fiber optic cable to the optical power meter input port. The UT693A-C01 supports 2.5mm universal connectors (FC/SC/ST).
3. Paspauskite Bangos ilgis button to cycle through the available calibration wavelengths (850nm, 980nm, 1270nm, 1300nm, 1310nm, 1490nm, 1550nm, 1577nm, 1625nm, 1650nm) until the desired wavelength is displayed.
4. The measured optical power will be displayed on the screen in dBm, dB, mW, or uW.
5. To set a reference value (REF), press and hold the REF button. This allows for relative power measurements.

Image: The UT693A-C01 in use, demonstrating fiber power measurement with a connected fiber optic cable and the VFL function active, showing the red light output.

5.2 Vizualinis gedimų ieškiklis (VFL)

The VFL function helps locate breaks, bends, and poor connections in fiber optic cables by emitting a bright red laser light.

1. Įsitikinkite, kad įrenginys įjungtas.
2. Connect the fiber optic cable to the VFL output port.
3. Paspauskite VFL button to activate the red laser.
4. Paspauskite VFL button again to switch between continuous wave (CW) mode and flashing mode.
5. Observe the fiber for any visible red light leakage, which indicates a fault.
6. Paspauskite VFL button once more to turn off the VFL.

5.3 RJ45 Network Cable Sequence Test

This function verifies the correct wiring sequence of RJ45 network cables.

1. Įsitikinkite, kad įrenginys įjungtas.
2. Connect one end of the RJ45 network cable to the RJ45 port on the UT693A-C01.
3. The device will automatically begin testing the cable sequence.
4. The display will show the wiring status, indicating if the cable is correctly wired (e.g., 1-8 sequence) or if there are any open circuits, shorts, or cross-overs.

Image: The UT693A-C01 performing an RJ45 cable sequence test, with a network cable connected and the display showing the test results.

5.4 Data Logging and Review

Įrenginys gali saugoti iki 500 matavimo duomenų rinkinių.

• To save a measurement, press and hold the Išsaugoti button after a stable reading is obtained.
• Norėdami iš naujoview stored data, refer to the specific instructions in the full user manual for navigation through saved records.

Image: The UT693A-C01 displaying stored data records, illustrating its 500-group data storage capacity.

5.5 LED žibintuvėlis

The integrated LED flashlight provides illumination for working in dark environments.

• To turn on the flashlight, press the dedicated flashlight button (if available) or a combination of buttons as indicated on the device.
• To turn off the flashlight, press the button again.

Image: The UT693A-C01 with its built-in LED flashlight active, illuminating a cable work area.

6. Priežiūra

6.1 Valymas

• Regularly clean the optical ports with a lint-free swab and optical cleaning solution to ensure accurate measurements.
• Wipe the exterior of the device with a soft, dry cloth. Do not use harsh chemicals or solvents.

6.2 Akumuliatoriaus priežiūra

• Įkraukite akumuliatorių, kai pasirodo žemos akumuliatoriaus įkrovos indikatorius.
• If storing the device for an extended period, charge it to approximately 50% every three months to prolong battery life.

7. Problemų sprendimas

This section addresses common issues you might encounter with the UT693A-C01.

8. Specifikacijos

The following table outlines the technical specifications for the UNI-T UT693A-C01.

Image: Detailed technical specifications table for the UT693A series, including the UT693A-C01 model, covering power measurement range, calibration wavelengths, interface, detector type, resolution, optical fiber transmission frequency, wavelength memory function, self-calibration, LED flashlight, backlight, red light source output power, red light wavelength, red light mode, network cable sequence test, charging interface, data storage, operating environment, storage environment, power supply, battery, product dimensions, product weight, and standard quantity per carton.

9. Garantija ir palaikymas

For warranty information and technical support, please refer to the warranty card included with your product or visit the official UNI-T websvetainėje. Išsaugokite pirkimo kvitą kaip pirkimo įrodymą.

Gamintojas: UNI-TREND TECHNOLOGY (CHINA) CO., LTD.