1. Įvadas
The MATEKSYS MBEC12S is a compact and efficient Micro Battery Eliminator Circuit (BEC) designed for various RC applications, including model airplanes, helicopters, and FPV racing drones. It converts a wide input voltage range of 6V to 60V DC into a stable, selectable output of 5V, 9V, or 12V DC, providing reliable power to your sensitive electronic components.
2. Specifikacijos
| Funkcija | Specifikacija |
|---|---|
| Įvesties tomastage Diapazonas | Nuo 6 V iki 60 V DC |
| Start-up Voltage | ≥ 6.7 V |
| Išėjimas ttage | 5V, 9V, or 12V DC (Adjustable, Default 5V) |
| Maksimalus darbo ciklas | 100% (Output voltage equals input voltage when input voltage is less than the set output voltage) |
| Budėjimo srovė | < 5 mA |
| Apsaugos ypatybės | Overcurrent Protection (OCP) with Hiccup, Thermal Shutdown, Output Short-circuit tolerant (3 seconds/minute) |
| Apsauga nuo atvirkštinio poliškumo | None for input |
| Smeigtuko atstumas | 2.54 mm |
| Matmenys | 18mm × 15(16)mm × 4.5mm |
| Svoris | 2g |
| Medžiaga | Sudėtinė medžiaga |
| Sertifikavimas | CE |
2.1. Continuous Load Current & Output Ripple
The continuous load current depends on the input voltage and heat dissipation. The following table provides typical continuous current ratings and output ripple values at room temperature (22°C) without an additional heat sink:
| 50V DC IN | 24V DC IN | 16V DC IN | Išvesties bangavimas | |
|---|---|---|---|---|
| 5 V IŠJ | 1.8A tęsinys. | 2.3A tęsinys. | 2.8A tęsinys. | 20mV |
| 3.5A Max. 2s/minute | ||||
| 9 V IŠJ | 1.5A tęsinys. | 2.1A tęsinys. | 2.6A tęsinys. | 30mV |
| 3A Max. 2s/minute | ||||
| 12 V IŠJ | 1.3A tęsinys. | 2A tęsinys. | 2.5A tęsinys. | 30mV |
| 3A Max. 2s/minute | ||||
3. Sąranka ir diegimas
- Išėjimas ttage pasirinkimas: The MBEC12S defaults to 5V output. To change the output voltage to 9V or 12V, you must bridge the corresponding solder pads on the module. Refer to Figure 2 for the location of the '9V' and '12V' pads.
- For 9V output: Bridge the '9V' solder pad.
- For 12V output: Bridge the '12V' solder pad.
- Ensure only one output voltage is selected at a time. Do not bridge both 9V and 12V pads simultaneously.
- Įvesties jungtis: Connect your power source (6V to 60V DC) to the 'IN' and 'GND' pads.
- 'IN' is for the positive (+) input voltage.
- 'GND' is for the negative (-) input voltage.
- ATSARGIAI: This module does NOT have protection for reversed input polarity. Ensure correct polarity when connecting the power source to avoid damage to the BEC and connected components.
- Išvesties jungtis: Connect your devices requiring regulated power to the 'OUT' and 'G' pads.
- 'OUT' provides the selected positive (+) output voltage (5 V, 9 V arba 12 V).
- 'G' is the common ground (-) for the output.
- Montavimas: The compact size (18x15mm) and light weight (2g) allow for flexible mounting. Secure the module using appropriate methods for your application, ensuring it is protected from vibrations and physical damage.
- Šilumos išsklaidymas: While the module is rated for continuous current without an additional heat sink at room temperature (22°C), consider airflow or an external heat sink for applications with high continuous loads or in environments with elevated temperatures to ensure optimal performance and longevity.
4. Operacija
Once correctly installed and powered, the MBEC12S will provide a stable, regulated DC output voltage as selected. The module operates with a maximum duty cycle of 100%, meaning if the input voltage drops below the set output voltage, the regulator's output will follow the input voltage (e.g., if set to 12V output but input drops to 10V, the output will be 10V).
Monitor the continuous load current to stay within the specified limits for your input voltage to prevent overcurrent conditions and ensure stable operation. Refer to the "Continuous Load Current & Output Ripple" table in Section 2.1 for guidance.
5. Priežiūra
The MATEKSYS MBEC12S is a robust electronic component designed for reliability. Minimal maintenance is required:
- Keep the module clean and free from dust, dirt, and moisture.
- Venkite modulio ilgalaikio laikymo itin aukštoje temperatūroje arba tiesioginiuose saulės spinduliuose.
- Regularly inspect solder joints and connections for any signs of wear or corrosion, especially in high-vibration environments.
- Ensure adequate airflow around the module, particularly during high-load operation, to prevent overheating.
6. Problemų sprendimas
- Nėra išvesties Voltage:
- Patikrinkite įvesties tūrįtage: Įsitikinkite, kad įvesties garsumastage is within the 6V-60V range and above the 6.7V start-up voltage.
- Check input polarity: Verify that the positive and negative input wires are connected correctly. Reversed polarity will damage the module.
- Check connections: Ensure all solder joints and wires are securely connected to the BEC and the load.
- Neteisingas išvesties garsumastage:
- Verify solder bridge: Confirm that the correct solder pad (9V or 12V) is bridged for your desired output, or that no pads are bridged for 5V output. Ensure only one pad is bridged.
- Module Overheating / Intermittent Operation:
- Reduce load: The module has Overcurrent Protection (OCP) and Thermal Shutdown. If it's overheating or shutting down, the load might be exceeding its continuous current capabilities. Refer to the specifications table.
- Improve cooling: Ensure sufficient airflow. Consider adding a small heat sink if operating at high loads or in warm environments.
- Output Short-circuit:
- The module is tolerant to output short-circuits for up to 3 seconds per minute. If a short occurs, disconnect power immediately, identify and resolve the short, then reconnect power. Prolonged short-circuits can damage the module.
7. Vartotojo patarimai
- Pre-flight/Pre-use Check: Always double-check all wiring connections and polarity before applying power to prevent damage to the BEC and other electronic components.
- ttage Patvirtinimas: Use a multimeter to verify the output voltage of the BEC before connecting it to your sensitive electronics, especially after adjusting the output voltage.
- Apkrovos valdymas: Be mindful of the continuous current ratings. If your application requires higher currents, ensure adequate cooling or consider a BEC with higher current capabilities.
- Litavimo kokybė: Use a fine-tipped soldering iron and good quality solder for bridging the voltage selection pads and connecting wires to ensure reliable electrical contact.
8. Garantija ir palaikymas
For technical support, troubleshooting assistance, or warranty inquiries, please contact your retailer or the manufacturer directly. Keep your purchase receipt as proof of purchase.
