1. Įvadas
This manual provides detailed instructions for the installation, operation, and maintenance of your LCD S830 Display and Brushless Controller. This system is designed to enhance the functionality and control of your electric bicycle, e-scooter, or e-car, offering features such as speed display, gear adjustment, and USB charging.
2. Pakuotės turinys
Prašome patikrinti, ar pakuotėje yra visi reikalingi daiktai:
- 1 x S830 Display
- 1 x Brushless Controller (250W, 350W, or 500W, depending on your selection)
3. Specifikacijos
S830 Display
- Produkto apvalkalas: ABS
- Grynasis svoris: 210g
- Pavaros režimas: 1-5
- ttage Įvertinimas: 24V/36V/48V
- Atsparumo vandeniui įvertinimas: IP65
- Montavimo skersmuo: 22mm (for handlebar)
Brushless Controllers
| Funkcija | 250W Controller | 350W Controller | 500W Controller |
|---|---|---|---|
| Įvertintas ttage | 24V/36V/48V | 24V/36V/48V | 24V/36V/48V |
| Nominali galia | 250W | 350W | 500W |
| Dabartinė išvestis | 13A ± 1A | 15A ± 1A | 25A ± 1A |
| Valdiklio dydis | 115 mm * 62 mm * 40 mm | 115 mm * 62 mm * 40 mm | 125 mm * 50 mm * 30 mm |
| Mosfetai | 6 Mos | 6 Mos | 9 Mos |
| Stabdžių įėjimas | Žemo lygio | Žemo lygio | Žemo lygio |
| Cutoff Voltage | 19/29/39V ± 0.5 | 19/29/39V ± 0.5 | 19/29/39V ± 0.5 |
Note: Controller dimensions are approximate and may vary slightly (1-3mm error).
4. Sąranka ir diegimas
IMPORTANT: The S830 Display and Brushless Controller must match the 2 communication protocol for proper operation. Ensure all connections are secure before powering on.
4.1 Laidų jungtys
Refer to the following diagrams for correct wiring. Ensure each wire is connected to its corresponding function.
Display Connection Wires:
- Red (VCC): Ekrano maitinimo laidas
- Blue (K): Valdiklio galios valdymo laidas
- Juoda (GND): Parodų aikštelė
- Žalia (RX): Display data receiving line
- Geltona (TX): Display data transmission line
Optional Light Wiring:
- Brown wire (DD): Light positive (+)
- White wire (GND): Light negative (-)
4.2 USB įkrovimo prievadas
The S830 Display includes a convenient USB charging port for mobile devices.
5. Naudojimo instrukcijos
The S830 Display offers powerful and easy-to-operate functions for your electric vehicle.
5.1 Pagrindinės operacijos
- Įjungti/išjungti: Long press the 'M' key to turn the display on or off.
- Pavaros reguliavimas: Use the 'Up' button to increase the gear and the 'Down' button to reduce the gear.
- Priekinių žibintų valdymas: Long press the 'Up' arrow key to turn on/off the headlights. The headlight icon will light up when active.
- Kruizo kontrolė: Long press the 'Down' arrow key to turn on/off cruise control. The cruise control icon will light up when active.
5.2 LCD Display Function Settings (P-Codes)
To enter mode selection, long press two buttons simultaneously. Navigate through the settings using the up/down buttons and confirm with the 'M' button. Long press two buttons again to exit mode selection.
- P01: Meter backlight brightness (1-3 levels)
- P02: Mileage unit (0: KM, 1: MILE)
- P03: ttage level (Base operating voltage)
- P04: Sleep Time (0: no-sleep, unit: min)
- P05: Assist position (0, 3, 1, 5 modes)
- P06: Wheel Diameter (unit: inch, Accuracy: 0.1)
- P07: Number of speed magnets (range: 1-100) - Note: This setting is for display only and does not affect actual speed.
- P08: Speed Limit (Range: 0-50km/h, 50: Unlimited speed) - When speed is higher than setting, turn off PWM output.
- P09: Zero or non-zero start (0: zero start, 1: non-zero start)
- P10: Drive Mode setting (0: Power Drive, throttle invalid; 1: Electric throttle Drive mode, Assist invalid; 2: Both assist and throttle are effective)
- P11: Boost sensitivity setting (range: 1-24)
- P12: Boost start strength setting (range: 1-5)
- P13: PAS Assist Type Setting (5/8/12) - Single Hall PAS: Set to 5/8, Double Hall PAS: Set to 12
- P16: ODO clear (long press up button for 5 seconds to clear)
6. Priežiūra
- Vandeniui atspari apsauga: The S830 Display has an IP65 waterproof rating. When using it in rainy conditions, ensure the USB rubber stopper is completely closed and wipe it dry in time after use to prevent water ingress.
- Valymas: Clean the display and controller with a soft, damp audinys. Venkite naudoti stiprių cheminių medžiagų ar abrazyvinių valiklių.
- Ryšio patikrinimai: Periodically check all wiring connections to ensure they are secure and free from corrosion or damage.
7. Problemų sprendimas
If you encounter issues, check the following:
- Ekranas neįsijungia: Ensure the main power to your e-bike/scooter is on and all connections to the display are secure.
- Klaidų kodai: The display may show error codes (e.g., E 06, E 07 as seen in the video). Consult the controller's specific error code documentation or contact support for interpretation.
- Incorrect Speed/Mileage: Verify P02 (Mileage unit) and P06 (Wheel Diameter) settings are correct for your setup.
- No Assist/Throttle Response: Check P09 (Start mode) and P10 (Drive Mode) settings. Ensure the PAS sensor and throttle connections are secure.
8. Vartotojo patarimai
- Greičio apribojimo reguliavimas: If you need to adjust the maximum speed, refer to the P08 setting in the LCD display functions. Be aware of local regulations regarding e-bike speed limits.
- Ryšio protokolas: Always ensure your display and controller are compatible and use the same communication protocol to avoid functionality issues.
9. Garantija ir palaikymas
For any technical assistance, warranty claims, or further inquiries, please contact the seller or manufacturer directly. Keep your purchase records handy for faster service.
