1. Įvadas
The HGLRC 5-12V BEC Step-down Module is a versatile power management component designed for RC FPV drones and similar applications. It efficiently converts a wide input voltage range (8.4V-28V) into stable 5V or 12V outputs, supporting a working current of up to 2A. This module offers flexible connection options, including direct soldering or wiring terminal connections, and features remote control channel support for switching the module on and off.
2. Produkto ypatybės
- Supports welding or wiring terminal connection for installation flexibility.
- Platus įvesties tūristage diapazonas: nuo 8.4 V iki 28 V.
- Dual output voltage modes: 5V and 12V.
- High working current: Up to 2A for stable performance.
- Remote control channel support for BEC module ON/OFF control.
3. Kas yra dėžutėje
Prašome patikrinti savo pakuotės turinį:
- HGLRC 5-12V BEC Module ×1
- Output cable ×1
4. Sąranka ir diegimas
4.1 Ryšio parinktys
The HGLRC 5-12V BEC module offers two primary methods for connection:
- Litavimas: Direct soldering to the designated pads on the module.
- Laidų terminalo jungtis: Using the provided wiring terminals for a plug-and-play solution.
4.2 Sujungimo schema
Refer to the following diagram for proper wiring of the BEC module. Ensure correct polarity when connecting power inputs and outputs.
- BAT (Positive Power Input): Connect your main battery (8.4V-28V, typically 2-6S LiPo) here.
- GND (Negative Power Input): Connect the negative terminal of your battery here.
- OUT+ (Positive Output): Provides the regulated 5V or 12V output. Connect to your electrical appliances (e.g., COB light strips).
- OUT- (Negative Output): Connect the negative terminal of your electrical appliances here.
- RX (Flight Control LED / TX): This pin is used for remote control channel integration to switch the BEC module on/off.
4.3 Išvesties ttage Selection (5V / 12V Mode Switch)
The module supports switching between 5V and 12V output modes:
- Default (Disconnected): When the solder joint (labeled "12V" on the board, near RX pin) is disconnected, the output voltage yra 5 V.
- 12V Output (Connected): When the solder joint is connected (bridged with solder), the output voltage yra 12 V.
Visada užtikrinkite teisingą tūrįtage is selected for your connected devices to prevent damage.
5. Naudojimo instrukcijos
Once the HGLRC 5-12V BEC module is correctly wired and the desired output voltage is selected, it will provide stable power to your connected components. The module also supports remote control functionality:
- Nuotolinio valdymo pulto įjungimas/išjungimas: Connect the RX pin to a suitable remote control channel on your flight controller. This allows you to remotely switch the BEC module's output on or off, providing greater control over your drone's accessories. Consult your flight controller's manual for specific instructions on configuring a channel for this purpose.
6. Priežiūra
To ensure the longevity and optimal performance of your HGLRC 5-12V BEC module, follow these maintenance guidelines:
- Laikyti švarų: Regularly inspect the module for dust, dirt, or debris. Use a soft, dry brush or compressed air to clean it.
- Venkite drėgmės: Protect the module from water and excessive humidity, which can cause short circuits and corrosion.
- Patikrinkite jungtis: Periodically check all soldered joints and wiring terminal connections to ensure they are secure and free from damage. Loose connections can lead to intermittent power supply or component failure.
- Temperatūros valdymas: Ensure adequate airflow around the module, especially during operation, to prevent overheating.
- Elkitės atsargiai: Avoid dropping or subjecting the module to strong impacts, as this can damage internal components.
7. Problemų sprendimas
If you encounter issues with your HGLRC 5-12V BEC module, refer to the following troubleshooting steps:
| Problema | Galima priežastis | Sprendimas |
|---|---|---|
| Nėra išėjimo tūriotage |
|
|
| Neteisinga išvestis ttage (e.g., 5V instead of 12V) |
|
|
| Modulio perkaitimas |
|
|
8. Specifikacijos
Detailed technical specifications for the HGLRC 5-12V BEC module:
| Parametras | Vertė |
|---|---|
| Vardas | HGLRC 5-12V BEC |
| Įvesties tomastage | 8.4V – 28V (Supports 2-6S LiPo) |
| Išėjimas ttage | 5V 2A / 12V 2A (Switchable) |
| Maksimali darbinė srovė | 2A |
| Matmenys | 12.1 mm × 21 mm |
| Svoris | 1.3g |
| Medžiaga | Sudėtinė medžiaga |
| Rekomenduojamas amžius | 14+ metų |
| Transporto priemonės tipui | Lėktuvai (RC FPV dronai) |
9. Vartotojo patarimai
Pateiktose ataskaitose nebuvo pateikta jokių konkrečių naudotojų patarimų.views or Q&A. However, general best practices for BEC modules include:
- Always double-check your wiring before applying power to avoid short circuits or damage to components.
- Užtikrinkite išvesties tūrįtage setting (5V or 12V) matches the requirements of the devices you are powering.
- Consider using heat shrink tubing or conformal coating for added protection in harsh FPV environments.
10. Garantija ir palaikymas
Dėl garantijos informacijos, techninės pagalbos ar paslaugų kreipkitės į gamintoją arba pirkimo vietą. Išsaugokite pirkimo įrodymą, jei prireiktų pateikti garantijos pretenziją.
