1. Įvadas
This manual provides essential information for the safe and efficient operation, setup, and maintenance of your Flipsky 65150 160KV 3000W Waterproof Brushless Motor with Built-in ESC. This high-performance motor is designed for applications such as electric surfing boards, boats, hydrofoils, and efoils. Please read this manual thoroughly before installation and use to ensure optimal performance and longevity of your product.
2. Saugos instrukcijos
Always prioritize safety when working with electric motors and watercraft. Failure to follow these instructions may result in injury, damage to the product, or property damage.
- Ensure all power sources are disconnected before performing any installation, maintenance, or inspection.
- Dėvėkite tinkamas asmenines apsaugos priemones (AAP), įskaitant akių apsaugą ir pirštines.
- Do not operate the motor if any components are damaged or show signs of wear.
- Laikykite rankas, plaukus ir laisvus drabužius atokiau nuo besisukančių dalių.
- This motor is waterproof, but ensure all connections are properly sealed and protected from water ingress during operation.
- Use only recommended voltage and current ratings to prevent overheating and damage.
- Mount the motor securely to prevent detachment during high-speed operation.
- Always test the motor in a controlled environment before full deployment.
3. Specifikacijos
The following table details the technical specifications of the Flipsky 65150 160KV motor:
| Funkcija | Specifikacija |
|---|---|
| Modelis | 65150 160KV |
| Dydis | ∅ 65mm * 150mm |
| KV įvertinimas | 160KV |
| ttage Diapazonas | 4-13S |
| Nominali srovė | 30A |
| Didžiausia srovė | 70A |
| Insulation Current | AC500v/1ma/3s |
| Nominali galia | 1500W |
| Didžiausia galia | 3000W |
| Vardinis sukimo momentas | 2.3 Nm |
| Maksimalus sukimo momentas | 4.5 Nm |
| Vidinė struktūra | 12N/10p |
| ESC Drive Mode | PPM |
| Ryšio uostas | USB, UART |
| ESC Driver Firmware | 5.2 VESC Tool 3.00 |
| ESC Support Mode | BLDC/FOC |
| Shaft Specifications | ∅ 12-0.005/-0.01 |
| Maitinimo laidas | 2*12AWG (∅ 4.5mm*140mm) |
| Maitinimo kištukas | XT90 Male |
3.1 Fiziniai matmenys
3.2 Propeller Dimensions
4. Pagrindinės savybės
- Neperšlampamas dizainas: Engineered for reliable operation in marine environments.
- Integrated ESC: Built-in Electronic Speed Controller simplifies setup and wiring.
- Didelio tikslumo Holo jutiklis: Located within the motor core for accurate position and temperature detection, ensuring smooth startup and precise control.
Figure 3: Hall sensor placement for precise detection and smooth motor start. - Multi-Strand Stator Winding: Utilizes multi-strand winding for superior heat dissipation and to mitigate the skin effect, enhancing efficiency.
Figure 4: Multi-strand stator winding for better heat dissipation and efficiency. - Durable Bearings: Features high-quality NMB bearings, with a double bearing configuration on the bottom side and one on top for enhanced durability and smooth operation.
Figure 5: Bearing configuration with NMB bearings for durability. - Robust Power Cable: Equipped with a 320mm super long, 12AWG silicon cable, highly heat-resistant and durable, packed with a braided sleeve for exquisite detail and protection.
Figure 6: Motor with 320mm 12AWG silicon power cable with braided sleeve.
5. Sąrankos instrukcijos
5.1 Išpakavimas ir patikrinimas
Carefully unpack all components and inspect for any visible damage. Ensure all parts listed in the package contents are present.
5.2 Variklio tvirtinimas
- Identify the mounting points on your application (e.g., efoil mast, boat transom).
- Align the motor's mounting holes with your application's mounting structure. The motor features 4-M4 mounting holes on a 42mm bolt circle diameter (refer to Figure 1).
- Secure the motor using M4 metric bolts (not included). Ensure the bolts are of appropriate length to securely fasten the motor without damaging internal components.
- Verify the motor is firmly attached and does not wobble.
5.3 Propelerio montavimas
- Įsitikinkite, kad variklio velenas yra švarus ir be šiukšlių.
- Slide the propeller onto the motor shaft. Ensure the propeller's shaft hole (10.2mm diameter) matches the motor's 12mm shaft (refer to Figure 2 for propeller dimensions). Some propellers may require an adapter or specific shaft type (round or stepped).
Figure 8: Motor with Round Shaft option. 
Figure 9: Motor with Stepped Shaft option. - Secure the propeller using the provided nut and washer. Tighten firmly but do not overtighten.
- Check that the propeller spins freely without obstruction.
5.4 Elektros jungtys
Refer to Figure 1 for the detailed wiring diagram.
- Maitinimo jungtis: Connect the motor's XT90 male power plug to a compatible XT90 female connector from your battery system. Ensure correct polarity (red to positive, black to negative). The power cord is 2*12AWG.
- Ryšio prievadai:
- PPM (impulso padėties moduliacija): Connect the 3-pin PPM cable to your receiver or control unit. Pinout: Black (GND), Red (5V), Yellow (SERVO).
- UART (Universal Asynchronous Receiver-Transmitter): Connect the 3-pin UART cable for serial communication. Pinout: White (Rx), Yellow (Tx), Black (GND), Red (5V).
- USB (Type-C): Use the Type-C USB port for connecting to a computer for ESC configuration and firmware updates using VESC Tool.
Figure 10: Motor with connected communication and power cables. - ESC konfigūracija: The motor features a built-in ESC with firmware 5.2 VESC Tool 3.00. Connect via the USB port to a computer running VESC Tool for initial setup, motor detection, and parameter adjustments (e.g., current limits, battery cutoffs, control modes).
6. Naudojimo instrukcijos
6.1 Prieš naudojimą kontrolinis sąrašas
- Įsitikinkite, kad visos elektros jungtys yra saugios ir izoliuotos.
- Verify the propeller is correctly installed and free from damage.
- Patikrinkite akumuliatoriaus įkrovos lygį.
- Confirm your remote control (if using PPM) is paired and functioning correctly.
6.2 Variklio užvedimas
- Power on your remote control first, then connect the battery to the motor's XT90 plug.
- The ESC will typically perform a self-test, indicated by a series of beeps.
- Slowly increase throttle input from your remote control. The motor should start smoothly due to the precise hall sensor detection.
- Observe motor behavior for any unusual noises, vibrations, or overheating.
6.3 valdymo režimai
The built-in ESC supports BLDC and FOC (Field-Oriented Control) modes. FOC generally offers smoother, quieter operation and better efficiency, while BLDC can provide higher top-end power. Configure your preferred mode using VESC Tool.
7. Priežiūra
Regular maintenance ensures the longevity and optimal performance of your Flipsky motor.
- Po kiekvieno naudojimo:
- Rinse the motor with fresh water, especially after saltwater use, to prevent corrosion.
- Inspect the propeller for any damage, chips, or entanglement with debris.
- Check all cables and connectors for wear, fraying, or corrosion.
- Periodic Checks (Monthly/Seasonally):
- Inspect motor mounting bolts for tightness.
- Check the motor shaft for any signs of bending or excessive play.
- Listen for unusual noises from the bearings during operation. While NMB bearings are durable, extreme conditions may require inspection.
- Ensure the braided sleeve on the power cable is intact and providing protection.
- Saugykla:
- Store the motor in a dry, cool place away from direct sunlight and extreme temperatures.
- If storing for extended periods, ensure the motor is clean and dry.
8. Problemų sprendimas
This section addresses common issues you might encounter with your motor.
| Problema | Galima priežastis | Sprendimas |
|---|---|---|
| Variklis nesisuka | No power, loose connections, faulty ESC/motor, remote issue. | Check battery connection and charge. Inspect all wiring. Verify remote control signal. Use VESC Tool to diagnose ESC/motor. |
| Motor stutters or runs rough | Incorrect ESC configuration, sensor issue, damaged motor phase wire. | Perform motor detection in VESC Tool. Check hall sensor connections. Inspect motor phase wires for damage. |
| Variklis perkaista | Excessive load, insufficient cooling, incorrect timing/settings. | Reduce load. Ensure adequate water flow for cooling. Adjust ESC settings (e.g., current limits, motor timing) in VESC Tool. |
| Propeller vibrates excessively | Damaged or unbalanced propeller, loose propeller. | Inspect propeller for damage and replace if necessary. Ensure propeller is securely tightened on the shaft. |
9. Vartotojo patarimai
- VESC Tool Configuration: Take time to properly configure your ESC using the VESC Tool. Accurate motor detection and setting appropriate current limits for your battery and application are crucial for performance and safety.
- Vandens sandarinimas: Although the motor is waterproof, always double-check the integrity of any external seals or connections, especially if you frequently submerge the unit.
- Propelerio pasirinkimas: Experiment with different propeller types (e.g., stepped vs. round shaft compatibility) and pitches to find the optimal balance of thrust and efficiency for your specific application.
10. Garantija ir palaikymas
Dėl garantijos informacijos, techninės pagalbos ar paslaugų kreipkitės tiesiogiai į pardavėją arba gamintoją. Išsaugokite pirkimo kvitą kaip pirkimo įrodymą.
