BEHRINGER CT200 Microprocessor-Controlled Cable Tester User Manual

Įvadas

The BEHRINGER CT200 is a microprocessor-controlled cable tester designed for comprehensive analysis of various cable types. It features three primary modes: cable test, installed cable test, and test tone mode. This versatile device accepts all standard connectors including XLR, Speakon, TRS (1/4", 1/8"), RCA, RJ45, MIDI, and USB. It provides super-easy operation with an intuitive LED display, offering continuity checks, intermittent contact detection, phantom-power checks, and ground-shield checks. This manual will guide you through the setup, operation, maintenance, and troubleshooting of your CT200 to ensure optimal performance.

Kas yra dėžutėje

• CT200 Microprocessor-Controlled Cable Tester
• Vartotojo vadovas (šis dokumentas)
• (Note: 2 AA batteries are required for operation and may not be included.)

Sąranka

1. Akumuliatoriaus montavimas: The CT200 requires two AA batteries for operation. Locate the battery compartment on the underside of the device. Unscrew the cover, insert the batteries according to the polarity markings, and replace the cover, ensuring the screw is securely fastened.
2. Maitinimas: Locate the power switch on the device. Slide it to the "ON" position. The LED display should illuminate, indicating the device is ready for use.
3. Režimo pasirinkimas: The CT200 offers different testing modes. Select the appropriate mode (Cable Tester, Test Tone, or Phantom) using the MODE switch based on your testing requirements.

Naudojimo instrukcijos

The CT200 provides intuitive testing for a wide range of cables. Follow these steps for effective cable analysis:

1. Cable Test Mode

• Set the MODE switch to "CABLE TESTER".
• Connect one end of the cable to an "INPUT" port and the other end to an "OUTPUT" port.
• The LED display will show the continuity of each pin. A lit LED indicates a good connection.
• The device checks for crossed wires, shorted connections, open circuits, and intermittent contacts.
• For cables with multiple pins (e.g., XLR), the display will show the connection status for each pin (Pin 1, Pin 2, Pin 3, Tip, Ring, Sleeve).
• If an issue is detected, the corresponding "CROSSED", "SHORTED", "OPEN", or "INTERMITTENT" LED will illuminate.

2. Bandymo tono režimas

• Set the MODE switch to "TEST TONE/PHANTOM".
• Select the desired tone level using the "TONE LEVEL" switch (+4 dBu, -10 dBV, or -50 dBV/MIC).
• Connect the cable to the appropriate output port (e.g., XLR OUT, 1/4" OUT).
• The CT200 will generate a test tone, which can be used to trace signals through a sound system or confirm signal flow.

3. Phantom Power and Ground-Shield Check

• In "TEST TONE/PHANTOM" mode, the device can also check for phantom power presence and ground-shield integrity.
• Connect an XLR cable to the XLR input. The "PHANTOM" LED will light up if phantom power is detected.
• The "GND/SHIELD PASS" LED indicates proper grounding.

4. Supported Connectors

The CT200 supports a wide array of connectors, making it an indispensable tool for audio professionals and enthusiasts:

• XLR (3 kontaktų)
• Speakon (4-pin)
• TRS (1/4" and 1/8")
• RCA
• RJ45 (Ethernet)
• MIDI (5-pin DIN)
• USB (Type A and B)

Demonstraciniai vaizdo įrašai

Priežiūra

• Valymas: Use a soft, dry cloth to clean the exterior of the CT200. Avoid using abrasive cleaners or solvents, as they may damage the finish or internal components.
• Baterijos keitimas: Replace batteries when the display dims or the device behaves erratically. Always use fresh AA batteries.
• Saugykla: Laikykite prietaisą vėsioje, sausoje vietoje, apsaugotoje nuo tiesioginių saulės spindulių ir ekstremalių temperatūrų.
• Jungčių priežiūra: Keep all input and output connectors free from dust and debris to ensure reliable connections and accurate readings.

Trikčių šalinimas

• Nėra galios:
  • Patikrinkite, ar baterijos tinkamai įdėtos ir ar jose pakankamai įkrovos.
  • Įsitikinkite, kad maitinimo jungiklis yra „ĮJUNGTA“ padėtyje.
• Netikslūs rodmenys:
  • Ensure cables are fully inserted into the correct input/output ports.
  • Clean connectors if they appear dirty or corroded.
  • Test with a known good cable to verify the tester's functionality.
• Intermittent Connection Indication:
  • If the "INTERMITTENT" LED lights up, gently flex the cable near the connectors while testing. This can help pinpoint loose or faulty internal connections.
  • This feature is particularly useful for diagnosing issues that are not constant breaks but occur under movement or stress.
• Phantom Power Not Detected:
  • Ensure the connected device is supplying phantom power.
  • Verify the XLR cable is functioning correctly with another test.

Specifikacijos

Garantija ir palaikymas

Dėl garantijos informacijos ir techninės pagalbos kreipkitės į oficialią „Behringer“ websvetainėje arba susisiekite tiesiogiai su jų klientų aptarnavimo tarnyba. Išsaugokite pirkimo kvitą kaip pirkimo įrodymą bet kokiems garantiniams prašymams.