Produktas baigtasview
The Tormek SG-200 Original Grindstone is designed for efficient steel removal and achieving a fine surface finish on various tools. This grindstone is compatible with Tormek T-4, T-3, and Tormek 1200 sharpening systems. Its unique composition allows for both coarse grinding (220 grit) and fine sharpening (simulating 1000 grit) when used with the Tormek Stone Grader SP-650.
Figure 1: The Tormek SG-200 Original Grindstone, showing its design and branding.
Saugos informacija
Always read and understand the full instruction manual of your Tormek sharpening system before operating. Wear appropriate personal protective equipment, including eye protection, when operating sharpening equipment. Ensure the grindstone is securely mounted and the machine is stable before use. Keep hands clear of moving parts. This product may expose you to chemicals known to the State of California to cause cancer and birth defects or other reproductive harm (Proposition 65 warning).
Sąranka ir diegimas
The SG-200 grindstone is designed for use with Tormek T-4, T-3, and Tormek 1200 sharpening systems. Refer to your specific Tormek machine's manual for detailed instructions on grindstone installation.
- Paruošimas: Ensure your Tormek sharpening system is unplugged and stable on a flat surface.
- Mounting the Grindstone: Carefully align the SG-200 grindstone with the shaft of your Tormek machine. Slide it onto the shaft, ensuring it seats properly.
- Apsauga: Attach the locking nut or securing mechanism as per your machine's instructions. Ensure the grindstone is firmly secured and rotates freely without wobble.
- Vandens lovelis: Fill the water trough with clean water to the recommended level, ensuring the lower part of the grindstone is submerged.
Figure 2: The Tormek SG-200 Grindstone mounted on a Tormek T-4 sharpening system, demonstrating its operational setup with a knife being sharpened.
Naudojimo instrukcijos
The Tormek SG-200 grindstone offers versatility for both efficient material removal and fine finishing. The grit can be adjusted using the Tormek Stone Grader SP-650.
Coarse Grinding (220 Grit)
For initial shaping, efficient material removal, or repairing damaged edges, use the grindstone in its normal 220-grit state. Ensure the stone is wet and rotate it in the direction recommended by your Tormek machine's manual. Apply light, consistent pressure with your tool against the rotating stone, using the appropriate jig.
Fine Sharpening (1000 Grit Equivalent)
To achieve a finer finish, similar to a 1000-grit stone, use the Tormek Stone Grader SP-650. Press the fine side of the Stone Grader against the rotating grindstone for approximately 30 seconds. This process polishes the surface of the grindstone, making it suitable for honing and fine sharpening. You can maintain the same jig settings as used for coarse grinding, which is a significant advantage for consistency.
Always ensure a continuous flow of water to the grindstone during operation to prevent overheating and maintain sharpening efficiency.
Priežiūra
Proper maintenance ensures the longevity and performance of your SG-200 grindstone.
- Valymas: After each use, clean the grindstone surface with a brush to remove any accumulated metal particles. This helps maintain its cutting ability.
- Persirengimas: Regularly dress the grindstone with the Tormek Stone Grader (SP-650) to maintain its true roundness and flatness. This is crucial for consistent sharpening results.
- Saugykla: When not in use, it is recommended to remove the grindstone from the water trough to prevent it from sitting in water for extended periods, which can affect its balance and performance over time. Store it in a dry place.
- Patikra: Periodically inspect the grindstone for any cracks, chips, or excessive wear. A damaged grindstone should be replaced immediately to ensure safety and optimal sharpening.
Trikčių šalinimas
This section addresses common issues you might encounter with your Tormek SG-200 grindstone.
| Problema | Galima priežastis | Sprendimas |
|---|---|---|
| Grindstone not cutting efficiently | Stone surface is glazed or clogged with metal particles. | Clean the stone surface with a brush. Use the coarse side of the Stone Grader SP-650 to refresh the surface. |
| Uneven sharpening results | Grindstone is not perfectly round or flat. | Dress the grindstone with the Tormek Stone Grader SP-650 to restore its true shape. Ensure proper jig setup. |
| Per didelė vibracija eksploatacijos metu | Grindstone not properly mounted or damaged. | Check if the grindstone is securely fastened. Inspect for cracks or damage; replace if necessary. |
| Stone appears to be losing grit | Normal wear over time, or improper storage. | This is a consumable item and will wear down. Ensure proper storage to prevent premature degradation. |
Specifikacijos
| Atributas | Detalė |
|---|---|
| Modelio numeris | SG-200 |
| Prekės ženklas | Tormek |
| Medžiaga | Alloy Steel Stone |
| Grit Range | 220 (normal) to 1000 (with Stone Grader SP-650) |
| Gaminio matmenys (I x P x A) | 9 cm x 8 cm x 2 cm (apytiksliai) |
| Prekės svoris | 2.3 kilogramų (5.06 svarai) |
| Suderinamumas | Tormek T-4, T-3, Tormek 1200 sharpening systems |
| Gamintojas | TORMEKAS |
Garantija ir palaikymas
Specific warranty information for the Tormek SG-200 Original Grindstone is typically provided with your Tormek sharpening system or can be found on the official Tormek website. As a consumable item, grindstones generally have a limited warranty against manufacturing defects.
For technical support, spare parts, or detailed warranty inquiries, please contact Tormek customer service directly or visit their official websvetainė:
- Tormek Official Websvetainė: www.tormek.com
- Refer to your Tormek machine's manual for specific contact details for your region.
