SainSmart 2-Channel Relay Module (Model 101-70-100) Instruction Manual

1. Įvadas

The SainSmart 2-Channel Relay Module is a versatile interface board designed for controlling high-current devices with low-voltage microcontrollers. It features two independent relays, each requiring 15-20mA driver current at 5V. The module is equipped with high-current relays capable of switching AC250V 10A or DC30V 10A. It provides a standard interface compatible with various microcontrollers such as Arduino, 8051, AVR, PIC, DSP, ARM, and MSP430, supporting TTL logic. Each relay includes an indication LED to show its output status.

Figure 1: SainSmart 2-Channel Relay Module. This image shows the overall view of the module with its two blue relays and screw terminals.

2. Kas yra dėžutėje

Upon opening the package, you will find the following item:

• 1 x SainSmart 2-Channel Relay Module

Figure 2: The SainSmart 2-Channel Relay Module shown with its retail packaging.

3. Sąranka

This section details the steps required to connect and prepare your 2-Channel Relay Module for operation with a microcontroller.

3.1. Smeigtuko aprašymas

3.2. Basic Wiring

1. Prijunkite GND pin of the relay module to the Ground (GND) pin of your microcontroller.
2. Prijunkite VCC pin of the relay module to the 5V power output of your microcontroller.
3. Prijunkite IN1 pin of the relay module to a digital output pin on your microcontroller (e.g., Digital Pin 10 on an Arduino).
4. (Pasirenkama) Prijunkite IN2 pin of the relay module to another digital output pin on your microcontroller for controlling the second relay.
5. For controlling the relay coils independently or with a different voltage, remove the jumper between JD-VCC and VCC. Then, connect an external 5V power supply to JD-VCC and ensure its ground is common with the microcontroller's ground.
6. Connect your high-current load to the appropriate K1 or K2 screw terminals. Each relay has three terminals: Normally Open (NO), Common (COM), and Normally Closed (NC).
   • To switch a device ON when the relay is activated, connect one side of the load to COM and the other side to NO.
   • To switch a device OFF when the relay is activated, connect one side of the load to COM and the other side to NC.

3 paveikslas: viršuje view of the relay module, highlighting the screw terminals for load connections.

4 pav.: Kampinis view of the relay module, showing the input pins (GND, IN1, IN2, VCC, JD-VCC).

5 pav. Apačia view of the relay module, showing solder points and mounting holes.

4. Modulio valdymas

The relay module is controlled by sending digital signals from your microcontroller to the IN1 and IN2 pins. The module typically uses active-LOW logic, meaning a LOW signal (0V) on an input pin will activate the corresponding relay, and a HIGH signal (5V or 3.3V depending on your microcontroller) will deactivate it.

4.1. Relay Activation Logic

• When the input pin (IN1 or IN2) receives a MAŽAS signal, the corresponding relay will activate (close the COM-NO circuit, open the COM-NC circuit). The onboard LED for that relay will illuminate.
• When the input pin (IN1 or IN2) receives a AUKŠTAS signal, the corresponding relay will deactivate (open the COM-NO circuit, close the COM-NC circuit). The onboard LED will turn off.

4.2. Pvzample Microcontroller Code (Conceptual)

For Arduino-compatible microcontrollers, you would typically use pinMode() to set the control pins as outputs and digitalWrite() to send HIGH or LOW signals.

void setup() {
  pinMode(10, OUTPUT); // Set digital pin 10 as an output for Relay 1
  digitalWrite(10, HIGH); // Ensure relay is off initially (active-LOW)
}

void loop() {
  digitalWrite(10, LOW);  // Activate Relay 1 (turn ON)
  delay(3000);            // Wait for 3 seconds
  digitalWrite(10, HIGH); // Deactivate Relay 1 (turn OFF)
  delay(3000);            // Wait for 3 seconds
}

Šis buvęsample demonstrates toggling Relay 1 every 3 seconds. Adjust pin numbers and delays as needed for your application.

5. Priežiūra

The SainSmart 2-Channel Relay Module is designed for durability and requires minimal maintenance. Follow these guidelines to ensure its longevity:

• Valymas: Keep the module free from dust and debris. Use a soft, dry cloth or a brush to gently clean the surface. Avoid using liquids or harsh chemicals.
• Saugykla: Store the module in a dry, cool environment away from direct sunlight and extreme temperatures. If not in use for extended periods, store it in an anti-static bag.
• Tvarkymas: Handle the module by its edges to avoid touching the electronic components, which can be sensitive to static discharge.
• Jungtys: Periodiškai patikrinkite visas laidų jungtis, kad įsitikintumėte, jog jos yra tvirtos ir be korozijos.

6. Problemų sprendimas

If you encounter issues with your SainSmart 2-Channel Relay Module, refer to the following common problems and solutions:

• Relay does not activate (LED does not light up):
  • Verify that the module is receiving 5V power at the VCC and JD-VCC pins and that GND is properly connected.
  • Ensure the control signal from your microcontroller to IN1/IN2 is a LOW (0V) signal. Remember, these modules are typically active-LOW.
  • Check the jumper between JD-VCC and VCC. If you are powering the relay coils separately, ensure this jumper is removed and JD-VCC has its own 5V supply.
  • Confirm that the microcontroller's digital output pin is correctly configured as an OUTPUT.
  • If using a 3.3V microcontroller, ensure the input current (approx. 20mA) can be sourced by the microcontroller's GPIO pins. Some users modify the module by replacing or adding parallel resistors to R1/R4 to reduce the current draw for 3.3V operation.
• Relay activates unexpectedly or flickers on startup:
  • This can occur if the microcontroller's digital output pin defaults to LOW during startup before your code sets it to HIGH. In your setup() function, ensure you set the pin to HIGH (to keep the relay off) prieš nustatymą pinMode() to OUTPUT.
• Load is not switching or is always ON/OFF:
  • Check the connections to the K1/K2 screw terminals. Ensure you are using the correct Normally Open (NO), Common (COM), and Normally Closed (NC) terminals for your desired operation.
  • Verify the load's power requirements do not exceed the relay's maximum ratings (AC250V 10A; DC30V 10A).
  • Confirm the load itself is functioning correctly.
• Audible "clack" sound when switching:
  • This is normal for mechanical relays and indicates the physical switching of the contacts. It is not a sign of malfunction.

7. Specifikacijos

8. Garantija ir palaikymas

Specific warranty information for the SainSmart 2-Channel Relay Module is not provided in the product details. For warranty claims, technical support, or further assistance, please contact SainSmart directly through their official websvetainėje arba mažmenininke, iš kurio įsigijote produktą.