1. Produktas baigtasview
This manual provides detailed instructions for the VDO SE51070 TPMS Service Kit, model SE10001HP. It is designed to assist users with the proper installation, operation, and maintenance of the Tire Pressure Monitoring System sensor.
Image 1: VDO SE51070 TPMS Service Kit (SE10001HP) sensor, showing the black sensor body attached to a silver metal valve stem.
2. Kas yra dėžutėje
The VDO SE51070 TPMS Service Kit (SE10001HP) typically includes:
- VDO SE51070 TPMS Service Kit (SE10001HP) sensor(s)
3. Specifikacijos
| Funkcija | Detalė |
|---|---|
| Prekės ženklas | VDO |
| Modelis | SE10001HP |
| Prekės matmenys (I x P x A) | 3.2 x 3.2 x 1.2 colio |
| Medžiaga | Plastikiniai |
| Prekės svoris | 2.08 uncijos |
| Matavimo tikslumas | ±1 % |
| Matavimo diapazonas | 20–80 PSI |
| Montavimo tipas | Flanšo tvirtinimas |
| Išvesties tipas | Mygtukas |
| Jutimo atstumas | 10 metrai |
| Viršutinės temperatūros įvertinimas | 120 laipsniai Celsijaus |
| Baterijos | Reikalinga 1 ličio metalo baterija (pridedama) |
| Compatible Makes | GM, Ford, Chrysler, Hyundai, Kia, Mazda, Mitsubishi, Nissan, Suzuki |
4. Sąranka ir diegimas
Proper installation of the TPMS sensor is crucial for accurate tire pressure monitoring. It is recommended that installation be performed by a qualified technician.
4.1 Patikrinimai prieš montavimą
- Ensure the wheel rim is clean and free from corrosion or foreign material around the valve stem hole. Clean thoroughly if necessary to ensure a proper, long-lasting seal.
- Verify that the correct TPMS sensor model (SE10001HP) is being used for your vehicle.
4.2 Sensor Assembly (if applicable)
Some TPMS sensors may require assembly of the sensor body to the valve stem. For the VDO SE10001HP, the sensor body is typically integrated with a metal valve stem.
- If your sensor comes with a separate metal valve stem and sensor body, use the square head bolt to thread the sensor body to the valve stem by hand. Ensure the square head portion aligns correctly with the groove on the TPMS body.
- The valve body and stem should be slightly loose at this stage (approximately two complete turns).
4.3 Jutiklių programavimas
Before installing the sensor into the wheel, it is recommended to program the sensor to the vehicle using a compatible TPMS programming tool. Consult your TPMS tool's manual for specific programming instructions.
Video 1: CDWTPS TPMS Sensor Introduction for GM series. This video demonstrates the general appearance and basic assembly of a TPMS sensor, including frequency and temperature range specifications.
Video 2: CARORAV GM Tire Pressure Sensor 315Mhz. This video highlights the sensor's specifications, replaceable valve stems, battery life, and signal strength, along with applicable vehicle models.
Video 3: FLORRIWAX Tire Pressure Monitoring System Sensor (019). This video provides a detailed breakdown of the sensor's components, temperature and pressure ranges, and warranty information.
Video 4: Installing EZ sensor 33500 with Snap-in Stem. PROGRAM FIRST! This video demonstrates the installation process for a snap-in TPMS sensor, emphasizing the importance of programming before installation.
Video 5: How to Install and Relearn TPMS Sensor. This video provides a step-by-step guide on installing and relearning a TPMS sensor, covering both physical installation and programming procedures.
Video 6: Tire Pressure Monitoring System Sensor 315MHZ TPMS Sensor. This video showcases the sensor's features, including its operating frequency, temperature range, and pressure range, along with a visual of its components.
Video 7: CARORAV TPMS Sensor fit for Nissan Infiniti 40700-JA01B. This video details the installation and relearning process for a specific Nissan/Infiniti TPMS sensor, including steps for programming and driving to complete the relearn.
Video 8: GM Tire Pressure Monitoring System Sensor 13586335 4PCS. This video provides an overview of the GM TPMS sensor, including its frequency, temperature range, and pressure range, along with a visual of the product.
4.4 Sensor Installation into the Wheel
- Once the sensor is programmed and the rim is clean, insert the valve stem from the inside of the rim through the mounting hole.
- For metal valve stems, use an 11mm socket and a 1/4 inch drive ratchet wrench to tighten the cap nut until it snugs up and some tension is felt. This tension is due to the cap nut contacting the additional upper seal.
- Finish tightening the cap nut to 35 inch-pounds (3.95 Newton meters) using a torque wrench. This ensures a proper, lasting seal and prevents overtightening and damage.
- For rubber valve stems, apply tire mounting lubricant to the outside of the valve stem. Use a valve stem installation tool to pull the valve stem all the way into the rim. Ensure the handle of the tool is in line with the valve stem to avoid damage.
- Verify proper installation: The sensor should not be touching the rim and should be free to move slightly. The groove on the sensor body should be seated in the rim, and the shoulders of the valve stem should be sitting on the edge both below and above the valve stem.
5. Naudojimo instrukcijos
After successful installation and programming, the TPMS sensor will begin monitoring your tire pressure. The vehicle's TPMS system will display tire pressure readings on the dashboard or infotainment system.
- Always maintain tire pressures as recommended by your vehicle manufacturer, typically found on a sticker inside the driver's side door jamb or in the owner's manual.
- If the TPMS warning light illuminates, check your tire pressures immediately and inflate them to the recommended levels.
6. Priežiūra
The VDO SE10001HP TPMS sensor is designed for long-term reliability. Regular maintenance involves:
- Baterijos veikimo laikas: The sensor is equipped with a lithium metal battery designed to last approximately 5 years or more. Battery replacement typically requires replacing the entire sensor.
- Valve Stem Service: It is recommended to replace the valve stem service kit (grommet, washer, nut, and valve core) whenever tires are serviced or replaced to ensure optimal sealing.
- Vizuali apžiūra: Periodically inspect the valve stems for any signs of damage, corrosion, or leaks.
7. Troubleshooting and Relearning
If your TPMS warning light remains on after tire inflation or sensor replacement, a relearn procedure may be necessary. Some vehicles may require specific steps to initiate the relearn process.
7.1 Common Relearn Procedures
Refer to your vehicle's owner's manual for the exact relearn procedure. Common methods include:
- Auto Relearn: Some vehicles automatically relearn new sensors after driving for a certain distance (e.g., 5-20 minutes at 40-50 mph).
- Manual Relearn (Paperclip Method for Nissan/Infiniti): For some Nissan/Infiniti models, a manual relearn can be performed by:
- Having a shop install and balance the sensor.
- Setting tire pressures to specific values (e.g., LF 36, RF 33, RR 30, RL 27 PSI) as close as possible.
- With the car off, locate a small white harness with a single wire near the ODB2 connector.
- Unbend an all-metal paperclip and insert it into the connector on the side with the wire.
- Turn the key to the "On" position (engine off). Within 10 seconds, tap the other end of the paperclip to ground 5 times (or continuously for 10 seconds).
- If successful, the TPMS light will switch from solid to blinking.
- Start the car, display the Tire Pressure status screen, and drive over 40 mph for several minutes (e.g., 3-5 miles) until all sensors register.
- Adjust tire pressures back to appropriate levels.
- OBD-II Relearn: Requires a TPMS diagnostic tool connected to the vehicle's OBD-II port to transfer new sensor IDs to the vehicle's ECU.
- Stacionarus pakartotinis mokymasis: Requires a TPMS activation tool to trigger sensors while the vehicle is in learn mode, often without driving.
Pastaba: Always follow your vehicle manufacturer's specific relearn and reprogramming procedures to ensure proper operation. If you are unsure, consult a professional mechanic.
8. Informacija apie garantiją
Specific warranty details for the VDO SE51070 TPMS Service Kit (SE10001HP) may vary. Please refer to the product packaging or contact VDO customer support for the most accurate and up-to-date warranty information.
9. Pagalba klientams
For technical assistance, troubleshooting, or any questions regarding your VDO SE51070 TPMS Service Kit (SE10001HP), please contact VDO customer support through their official websvetainėje arba kontaktinėje informacijoje, pateiktoje kartu su jūsų produktu.
