ESI Ultimate galinio dangčio sandariklis su kūginiu sandarikliu, 6 pėdų (1,8 m) naudojimo instrukcija

1. Įvadas

This manual provides detailed instructions for the proper installation and use of the ESI Ultimate Tailgate Seal with Taper Seal 6ft. This product is designed to create a tight seal around your truck's tailgate, effectively keeping out dust, water, and snow from your truck bed. Following these instructions will ensure optimal performance and longevity of your tailgate seal.

2. Pakuotės turinys

The ESI Ultimate Tailgate Seal package typically includes:

• 6ft length of Ultimate Tailgate Seal with Taper Seal
• Alcohol prep pads (for surface cleaning)

Figure 1: ESI Ultimate Tailgate Seal with Taper Seal 6ft.

3. Suderinamumas

This 6ft length seal is designed to seal either the sidewalls OR the tailgate bottom gap. For complete sealing of both sidewalls and the tailgate bottom gaps, a 10ft length kit is recommended (search ASIN: B00IPQWXZQ).

Compatible Use Cases:

• Use on sidewalls when using a ROK BLOCK (ASIN: B00BPE4AP6).
• Use on sidewalls when using a BedRug truck bed liner that covers only the tailgate bottom gap.

Known Incompatible Trucks:

• 2020 and newer Silverado and Sierra 2500 and 3500
• Sierra with MultiPro Tailgate
• Sierra EV
• Silverado with Multi-Flex Tailgate
• Silverado EV
• Ford Lightning
• Ford Maverick
• Ford Raptor
• Ford with Pro Access Tailgate
• Honda Ridgeline
• RAM with RamBox
• RAM with RamBox and Multifunction Tailgate
• Titanas
• Tacoma 2024 and newer
• Tundra 2022 and newer

4. Montavimas

Proper installation is crucial for the effectiveness of the tailgate seal. Please follow these steps carefully.

4.1. Paruošimas

1. Ensure the air and surface temperature is between 55°F - 104°F (13°C - 40°C) for optimal adhesive bonding.
2. Thoroughly clean the application area on your truck bed and tailgate using the provided alcohol prep pads or a suitable degreaser. The surface must be dry and free of dust, dirt, wax, or oil.
3. Test fit the seal along the intended path to determine the correct placement and any necessary cuts.

4.2. Paraiškos teikimo etapai

4. Begin by peeling back a small section of the red adhesive liner from one end of the seal.
5. Carefully align the exposed adhesive portion with the cleaned surface of your truck bed or tailgate. Apply light pressure to secure it.
6. Gradually peel off more of the red liner while pressing the seal firmly into place. Work in small sections to ensure a straight and secure application.
7. For corners or tight areas, you may need to cut smaller pieces of the seal to fit. Ensure all edges are pressed down firmly.
8. Apply at least 25 lbs. of pressure along the entire length of the installed seal to ensure proper bonding of the adhesive. You can use a roller or firmly press with your hand.
9. After installation, keep the tailgate closed for at least 24 hours to allow the adhesive to cure and achieve maximum bond strength. Avoid exposing the seal to water for approximately 3 days.

Figure 2: Tailgate seal applied to the truck bed side.

Figure 3: Large Taper Seal piece installation.

Figure 4: Tailgate seal applied to a truck bed corner.

4.3. Diegimo vaizdo įrašai

For visual guidance, please refer to the following official installation videos:

5. Produkto ypatybės

• Medžiaga: Made from all-weather grade, UV, gas, and oil resistant EPDM industrial high-strength rubber.
• Sandarinimas: Creates a tight seal to keep dust, rain, and snow out of your truck bed.
• Klijai: Features a strong adhesive backing for secure attachment.
• Patvarumas: Designed for long-lasting performance in various environmental conditions.

6. Specifikacijos

7. Priežiūra

To maintain the effectiveness and longevity of your ESI Ultimate Tailgate Seal:

• Periodically inspect the seal for any signs of wear, damage, or detachment.
• Clean the seal and surrounding area with mild soap and water as needed. Avoid harsh chemicals that could degrade the rubber or adhesive.
• Ensure the adhesive remains firmly attached. If any section begins to lift, reapply pressure or consider replacing the affected section if necessary.

8. Problemų sprendimas

8.1. Incomplete Seal / Dust or Water Intrusion

• Patikrinkite diegimą: Re-verify that the seal was applied to a clean, dry surface within the recommended temperature range. Ensure sufficient pressure (25 lbs.) was applied during installation.
• Inspect Placement: Confirm the seal is positioned correctly to cover all gaps. Some truck models may require inverting the seal's bulb for a tighter fit (refer to Video 3 in the Installation section).
• Additional Gaps: Check for other potential entry points for dust or water, such as gaps in the front corners of the truck bed, especially if using a truck cap or tonneau cover. These may require additional sealing solutions.

8.2. Seal Detachment

• Paviršiaus paruošimas: Ensure the surface was thoroughly cleaned and dry before application. Any residue can prevent proper adhesion.
• Kietėjimo laikas: Allow the full 24-hour curing period with the tailgate closed, and avoid water exposure for 3 days, to ensure maximum adhesive bond.
• Pakartotinis naudojimas: If a small section detaches, clean the area, apply new adhesive if necessary, and firmly press the seal back into place. For significant detachment, consider replacing the seal.

9. Garantija ir palaikymas

For specific warranty information or technical support, please refer to the product packaging or contact Extruded Solutions Inc (ESI) directly. Contact details can typically be found on the manufacturer's websvetainėje arba ant produkto pakuotės.