AntMiner S9 naudojimo instrukcija

1. Produktas baigtasview

The AntMiner S9 is a high-performance ASIC (Application-Specific Integrated Circuit) miner designed for Bitcoin mining. It features a hash rate of approximately 13.5 TH/s and is known for its power efficiency. This manual provides essential information for the proper setup, operation, and maintenance of your AntMiner S9.

1.1 paveikslas: Priekinė pusė view of the AntMiner S9, showcasindėl kompaktiško dizaino ir integruotų aušinimo ventiliatorių.

2. Saugos informacija

• Ensure the power supply unit (PSU) is connected to a stable power source.
• Do not connect more than one PSU to the same hash board to prevent potential damage and instability.
• Operate the miner within the specified temperature range of 0 °C to 40 °C.
• Keep the device away from water, moisture, and high humidity.
• Do not attempt to open or modify the miner, as this may void the warranty and pose safety risks.
• Ensure adequate ventilation around the miner to prevent overheating.

3. Pakuotės turinys

Patikrinkite, ar pakuotėje yra visi reikalingi daiktai:

• AntMiner S9 ASIC Bitcoin Miner
• Maitinimo blokas (PSU)
• Maitinimo laidas

4. Sąrankos vadovas

4.1 Maitinimo jungtis

The AntMiner S9 requires TEN 6-pin PCI-e connectors for 12V DC input. These connectors must be supplied by a very stable power source.

1. Locate the three hash boards, each requiring three 6-pin PCI-e connectors.
2. Locate the controller board, which requires one additional 6-pin PCI-e connector.
3. Connect all TEN 6-pin PCI-e connectors from the power supply unit to the respective ports on the miner.
4. Įsitikinkite, kad visos jungtys yra saugios.
5. Connect the power cord from the PSU to a suitable electrical outlet.

Svarbi pastaba:

• Bitmain recommends the APW3 power supply for 205-264V outlets. For voltages lower than 205V, use the EVGA 1600 G2.
• Power consumption figures are dependent on PSU efficiency, ambient operating temperature, and power meter accuracy.

Image 4.1: Front panel of the AntMiner S9, showing the Ethernet port, IP Report button, SD card slot, and status indicator lights.

4.2 Tinklo jungtis

The AntMiner S9 connects to your network via an Ethernet cable.

1. Connect one end of an Ethernet cable to the ETH port on the AntMiner S9.
2. Prijunkite kitą Ethernet kabelio galą prie maršrutizatoriaus arba tinklo komutatoriaus.
3. Once connected, the miner will automatically obtain an IP address via DHCP.

5. Naudojimo instrukcijos

5.1 Prieiga prie Web Valdymo portalas

The AntMiner S9 features a built-in web management portal, eliminating the need for a separate host computer for configuration.

1. Ensure the miner is powered on and connected to your network.
2. To find the miner's IP address, you can use an IP scanner tool on your network or press the "IP Report" button on the miner. Hold the button for 5 seconds until you hear a beep. The IP address will be reported to the IP Reporter tool (available from Antminer support).
3. Atidarykite a web naršyklę kompiuteryje, prijungtame prie to paties tinklo.
4. Enter the miner's IP address into the browser's address bar and press Enter.
5. You will be prompted for login credentials. The default username and password are typically "root" and "root" (or "admin" and "admin"). Refer to the latest Antminer documentation for default credentials.
6. Once logged in, you can configure mining pool settings, monitor performance, and update firmware.

5.1 paveikslėlis: Šonas view of the AntMiner S9, illustrating its robust casing and fan placement.

5.2 Configuring Mining Pools

Per web management portal, navigate to the "Miner Configuration" or "Pool Settings" section to enter your mining pool details. You will typically need to provide:

• Baseinas URL: The address of your chosen mining pool.
• Worker Name: Your worker name, usually in the format username.workername.
• Slaptažodis: The password for your worker (often 'x' or a specific password set on the pool).

It is recommended to configure at least two mining pools (primary and backup) for continuous operation.

6. Priežiūra

• Dulkių šalinimas: Regularly inspect and clean the cooling fans and heat sinks to prevent dust buildup, which can impede airflow and lead to overheating. Use compressed air for effective cleaning.
• Aplinkos kontrolė: Maintain a stable operating environment with good airflow and within the recommended temperature range (0 °C to 40 °C).
• Firmware atnaujinimai: Periodically check the official Antminer websvetainės, kurioje rasite programinės įrangos atnaujinimus. Nuolat atnaujinant programinę įrangą galima pagerinti našumą ir stabilumą.
• Maitinimo patikrinimas: Ensure the power supply unit is functioning correctly and providing stable voltage.

7. Problemų sprendimas

For more complex issues, refer to the official Antminer support resources or contact customer support.

8. Specifikacijos

9. Garantija ir palaikymas

This product is covered by the manufacturer's warranty. For any issues covered under the manufacturer warranty, please handle them directly with the manufacturer. The seller's return policy may involve restocking fees if troubleshooting and technical support are not sought prior to a return.

For technical assistance, troubleshooting, or warranty claims, please contact the manufacturer or your seller's support channels. It is often possible to resolve issues quickly without needing to return the unit.

Legal Disclaimer: By purchasing this product, you agree to seek troubleshooting and technical support from the seller and/or manufacturer before attempting a return. Returns without seeking technical support and troubleshooting may be subject to restocking fees.