„Hilti CP 606“ priešgaisrinio sandariklio naudojimo instrukcija

1. Produktas baigtasview

The Hilti CP 606 Firestop Sealant is a high-performance, intumescent acrylic sealant designed for firestopping applications. It expands when exposed to heat, forming a fire-resistant barrier that helps prevent the spread of fire and smoke through penetrations in fire-rated constructions. This product is suitable for various joint and penetration sealing applications in walls and floors.

An image showing a single 10.5oz tube of Hilti CP 606 red firestop sealant, clearly displaying the Hilti logo and product identification.

2. Saugos informacija

Always prioritize safety when working with sealants. Read and understand the Safety Data Sheet (SDS) before use. Observe all local safety regulations.

• Asmeninės apsaugos priemonės (AAP): Wear appropriate PPE, including safety glasses, gloves, and protective clothing, to prevent skin and eye contact.
• Vėdinimas: Use in well-ventilated areas. If adequate ventilation is not available, use respiratory protection.
• Kontaktas su oda: Patekus ant odos, gerai nuplauti vandeniu ir muilu.
• Akių kontaktas: In case of eye contact, flush immediately with plenty of water for several minutes and seek medical attention.
• Nurijimas: Nenuryti. Prarijus, nedelsiant kreiptis į gydytoją.
• Laikykite nepasiekiamoje vietoje: Laikyti vaikams ir naminiams gyvūnėliams nepasiekiamoje vietoje.

3. Sąranka ir paruošimas

1. Paviršiaus paruošimas: Ensure all surfaces to be sealed are clean, dry, and free from dust, oil, grease, loose particles, and other contaminants. Substrates should be sound and stable.
2. Joint Dimensions: Verify that joint dimensions are within the product's specified limits for optimal performance.
3. Pagrindo medžiaga: For deeper joints, use a suitable backing material (e.g., backer rod) to control sealant depth and ensure proper sealant geometry.
4. Reikalingi įrankiai:
   • Standard caulking gun
   • Utility knife or sealant cutter
   • Trowel or tooling stick for finishing
   • Cleaning supplies (rags, appropriate solvent if needed)
5. Temperatūra: Apply the sealant within the recommended temperature range, typically between 5°C and 40°C (41°F and 104°F).

4. Taikymo instrukcijos

1. Prepare Cartridge: Cut the tip of the sealant tube at a 45-degree angle to the desired bead size. Puncture the inner seal of the cartridge.
2. Load Caulking Gun: Insert the prepared cartridge into a standard caulking gun.
3. Užtepkite sandariklį: Apply the sealant evenly and continuously into the joint or penetration, ensuring full contact with the substrate. Maintain consistent pressure on the trigger to achieve a smooth, uniform bead.
4. Įrankiai: Within 5-10 minutes of application (before skinning occurs), tool the sealant to ensure good adhesion and a smooth finish. Remove any excess sealant immediately.
5. Kietėjimas: The sealant will skin over in approximately 15-30 minutes, depending on temperature and humidity. Full cure time can range from several days to weeks, depending on bead thickness and environmental conditions. Protect the freshly applied sealant from water and heavy traffic until fully cured.

5. Priežiūra

Once cured, Hilti CP 606 Firestop Sealant requires minimal maintenance. Periodically inspect sealed joints and penetrations for any signs of damage, cracking, or degradation. If damage is observed, clean the area and reapply sealant as necessary to maintain the firestop integrity.

6. Problemų sprendimas

• Prastas sukibimas:

  Ensure surfaces are clean, dry, and free of contaminants. Proper surface preparation is critical for good adhesion.
• Slow Curing:

  Low temperatures and high humidity can extend curing times. Ensure adequate ventilation and maintain recommended application temperatures.

• Cracking or Shrinkage:

  Excessive joint movement or improper joint design can lead to cracking. Ensure correct joint dimensions and use of backing material where appropriate.

7. Specifikacijos

8. Sandėliavimas ir šalinimas

• Saugykla: Store the sealant in its original, unopened packaging in a cool, dry place, away from direct sunlight and extreme temperatures. Recommended storage temperature is typically between 5°C and 25°C (41°F and 77°F).
• Šalinimas: Dispose of unused product and empty containers in accordance with local, state, and federal regulations. Do not dispose of in drains or waterways. Consult local waste management authorities for proper disposal methods.

9. Garantija ir palaikymas

For specific warranty information regarding the Hilti CP 606 Firestop Sealant, please refer to the official Hilti website or contact Hilti customer service directly. Hilti provides comprehensive technical support and product documentation to assist with proper application and performance.

„Hilti“ oficialus Websvetainė: www.hilti.com