„Dinuy Terminal Micro 5“ skaitmeninio laiko jungiklio naudotojo vadovas

1. Įvadas

This manual provides comprehensive instructions for the installation, operation, and maintenance of your Dinuy Terminal Micro 5 Digital Time Switch. Please read this manual carefully before using the device to ensure safe and efficient operation. This device is designed to control electrical circuits based on programmed time schedules.

2. Svarbi saugos informacija

• Elektros pavojus: Installation and maintenance should only be performed by a qualified electrician in accordance with all local and national electrical codes.
• Disconnect power at the main circuit breaker before installing or servicing the device.
• Nelaikykite įrenginio drėgmės, ekstremalių temperatūrų ar korozinės aplinkos veikiamo.
• Įsitikinkite, kad visos jungtys yra tvirtos ir tinkamai izoliuotos, kad išvengtumėte trumpojo jungimo.
• Do not exceed the maximum load capacity specified for the device.

3. Produktas baigtasview

The Dinuy Terminal Micro 5 is a compact digital time switch designed for DIN rail mounting. It features a clear LCD display for time and program status, along with intuitive buttons for easy programming.

Figure 1: Dinuy Terminal Micro 5 Digital Time Switch

This image displays the Dinuy Terminal Micro 5 digital time switch. The device is white, designed for DIN rail mounting. The top section shows terminals labeled '1' and '2' for power input. Below this, there are terminals '1', '2', '3' for the switched output, with a rating of 'μ16(6)A 250V~'. The central part features a digital LCD screen displaying 'DINUY', '18.06.18', 'LUNES' (Monday), 'On', and '9:28.00'. Below the screen are four blue buttons: 'M' (Mode), 'OK', '-' (Minus/Left arrow), and '+' (Plus/Right arrow). The bottom section shows terminals 'N' (Neutral) and 'L' (Live) for the main power supply, with '230V/50-60Hz' indicated.

3.1. Komponentai

• LCD ekranas: Shows current time, day, program status, and programming menus.
• „M“ mygtukas (režimas): Used to navigate through different modes (e.g., time setting, program setting).
• 'OK' Button: Patvirtina pasirinkimus ir nustatymus.
• '-' Button (Minus/Left Arrow): Decreases values or moves left in menus.
• '+' Button (Plus/Right Arrow): Increases values or moves right in menus.
• Terminals L & N: Main power supply input (230V/50-60Hz).
• 1, 2, 3 terminalai: Switched output contacts (μ16(6)A 250V~).

4. Diegimas ir sąranka

4.1. Montavimas

The Dinuy Terminal Micro 5 is designed for DIN rail mounting. Snap the device onto a standard 35mm DIN rail in your electrical panel.

4.2. Laidų schema

ĮSPĖJIMAS: Prieš prijungdami laidus, įsitikinkite, kad maitinimas yra atjungtas.

1. Connect the main Live (L) wire to the 'L' terminal at the bottom of the device.
2. Connect the main Neutral (N) wire to the 'N' terminal at the bottom of the device.
3. For the switched output, connect the load's Live wire to terminal '1' or '3' (depending on desired contact type, typically '1' for normally open).
4. Connect the incoming Live wire for the load to terminal '2'.
5. Refer to the markings on the device for precise terminal identification: Input power (L, N) and Switched output (1, 2, 3).

4.3. Pradinis įjungimas

After wiring, restore power. The display should illuminate. If the display is blank, check power connections. The device may require initial time and date setting.

5. Naudojimo instrukcijos

5.1. Dabartinio laiko ir dienos nustatymas

1. Press the 'M' button repeatedly until the time setting mode is displayed (e.g., flashing hours).
2. Use the '+' and '-' buttons to adjust the hour. Press 'OK' to confirm.
3. Repeat for minutes, then for the current day of the week.
4. Press 'OK' to save and exit the time setting mode.

5.2. Įjungimo/išjungimo tvarkaraščių programavimas

The device allows setting multiple ON/OFF programs for different days or groups of days.

1. Press the 'M' button until 'PROG' or a similar indicator appears.
2. Use '+' or '-' to select a program number (e.g., '1 ON'). Press 'OK'.
3. Set the desired ON time (hour and minute) using '+' and '-' and confirming with 'OK'.
4. Select the days for this program (e.g., Mon-Fri, daily, specific days) using '+' and '-' and confirming with 'OK'.
5. Repeat for the corresponding OFF time ('1 OFF').
6. Continue for additional programs as needed.
7. Press 'M' to exit programming mode and return to normal operation.

5.3. Rankinis nepaisymas

To temporarily override the programmed schedule, press the 'M' button briefly during normal operation. This will cycle through 'ON', 'OFF', and 'AUTO' modes. Select 'AUTO' to resume programmed operation.

6. Priežiūra

The Dinuy Terminal Micro 5 requires minimal maintenance. Ensure the device is kept clean and free from dust. Use a soft, dry cloth for cleaning. Do not use abrasive cleaners or solvents.

7. Problemų sprendimas

• Įrenginys neįsijungia: Check main power supply and wiring connections (L and N terminals). Ensure the circuit breaker is on.
• Load not switching: Verify that the program is correctly set and the device is in 'AUTO' mode. Check the load's wiring and functionality. Ensure the load does not exceed the device's maximum switching capacity.
• Neteisingas laiko rodymas: Reset the current time and day as per section 5.1.
• Programs not executing: Ensure the device is in 'AUTO' mode. Recheck program settings for correct ON/OFF times and selected days.

8. Techninės specifikacijos

9. Informacija apie garantiją

This product is covered by the manufacturer's standard warranty. Please refer to the warranty card included with your purchase or contact Dinuy customer support for detailed warranty terms and conditions. Keep your proof of purchase for warranty claims.

10. Pagalba klientams

For technical assistance, troubleshooting not covered in this manual, or warranty inquiries, please contact your local Dinuy distributor or visit the official Dinuy websvetainė kontaktinei informacijai.