1. Produktas baigtasview
The EBARA AGA 0.75 M is a robust single-phase self-priming electric pump constructed from cast iron, designed for efficient clean water transfer. Its applications include domestic water pressure boosting, small-scale garden irrigation, vehicle washing, and general water movement tasks.
This image shows the EBARA AGA 0.75 M self-priming pump, featuring a blue cast iron body and an integrated electric motor with a black terminal box on top. The pump has visible inlet and outlet connections.
2. Sąranka ir diegimas
Proper installation is crucial for the pump's performance and longevity. Follow these general guidelines:
- Vieta: Install the pump in a dry, well-ventilated area, protected from frost and direct sunlight. Ensure a stable, level surface to minimize vibration.
- Vamzdžių jungtys: Connect the suction pipe to the pump's G1 suction port and the delivery pipe to the G1 delivery port. Ensure all connections are airtight to prevent air ingress, which can affect priming. Use appropriate sealants and fittings.
- Elektros jungtis: The pump operates on 230 V ± 10% 50 Hz single-phase power. Connect the pump to a suitable electrical supply according to local regulations. Ensure the circuit is protected by a permanent capacitor and an automatic reset thermal-amperometric protection device.
- Gruntavimas: As a self-priming pump, it can draw water from a certain depth (up to 8m). Before initial startup, fill the pump body completely with clean water through the priming port until it overflows. This ensures the pump can establish suction.
3. Naudojimo instrukcijos
Įrengus ir užpildžius siurblį, jis paruoštas darbui:
- Pradinis paleidimas: After priming, switch on the power supply. The pump should start drawing water and build pressure.
- Stebėjimas: Observe the pump during operation. Listen for unusual noises and check for leaks. Ensure consistent water flow and pressure.
- Nepertraukiamas veikimas: The pump is designed for continuous duty within its specified operating limits. Avoid running the pump dry, as this can cause damage to the mechanical seal.
- Išjungti: To stop the pump, simply switch off the power supply.
4. Priežiūra
Regular maintenance helps ensure the longevity and efficient operation of your pump:
- Reguliarus patikrinimas: Periodically check all connections for leaks and ensure the pump is securely mounted. Inspect the power cable for any damage.
- Valymas: Keep the pump exterior clean and free from debris. Ensure the motor's ventilation fins are not obstructed to prevent overheating.
- Žieminimas (jei taikoma): In areas prone to freezing temperatures, drain the pump completely to prevent damage from ice expansion. Disconnect pipes and open drain plugs. Store the pump in a frost-free environment if possible.
- Mechaninis sandariklis: The mechanical seal is a wear part. If persistent leaks occur from the shaft area, the seal may need replacement by a qualified technician.
5. Problemų sprendimas
Šiame skyriuje aptariamos dažniausiai pasitaikančios problemos, su kuriomis galite susidurti:
| Problema | Galima priežastis | Sprendimas |
|---|---|---|
| Siurblys neįsijungia | No power supply; Motor overload protection tripped; Seized impeller | Check power connection and circuit breaker; Allow motor to cool and reset protection; Contact qualified technician. |
| Siurblys veikia, bet vanduo neteka | Pump not primed; Air leak in suction line; Suction lift too high; Clogged suction filter | Re-prime the pump; Check all suction connections for leaks; Ensure suction depth is within 8m limit; Clean suction filter. |
| Low pressure or reduced flow | Partial air leak; Partially clogged impeller/pipes; Worn impeller or mechanical seal | Check suction line for small leaks; Inspect and clean impeller/pipes; Contact qualified technician for inspection. |
| Per didelis triukšmas ar vibracija | Kavitacija (oras vandenyje); Atsilaisvinęs tvirtinimas; Guolių susidėvėjimas | Ensure proper priming and no air leaks; Securely fasten pump; Contact qualified technician. |
6. Specifikacijos
| Funkcija | Detalė |
|---|---|
| Gamintojas | Ebara |
| Modelio numeris | 1100090000 |
| Medžiaga | Ketaus |
| Maitinimo šaltinis | Su laidu elektra |
| ttage | 230 voltai (kintamoji srovė) |
| Maksimalus darbinis slėgis | 6 barų |
| Maksimali skysčio temperatūra | 45 °C |
| Didžiausias įsiurbimo gylis | 8 m |
| Siurbimo jungtis | G1 |
| Delivery Connection | G1 |
| Variklio efektyvumas | IE2 and IE3 (from 0.75 kW) |
| Izoliacijos klasė | F |
| Apsaugos laipsnis | IP44 |
| Pakuotės matmenys | 40.5 x 18.5 x 18 cm |
| Prekės svoris | 12.5 kilogramo |
| Baterijos įtrauktos | Nr |
| Reikalingos baterijos | Nr |
| Atsarginių dalių prieinamumas | Informacija nepasiekiama |
7. Garantija ir palaikymas
For warranty information and technical support, please refer to the documentation provided with your purchase or contact your authorized Ebara dealer. Information regarding spare parts availability is currently not provided in the product specifications.
