Boulder Pro 36x10W RGBW LED Moving Head Wash Beam Stage Light naudojimo instrukcija

1. Įvadas

This manual provides essential information for the safe and effective operation of your Boulder Pro 36x10W RGBW LED Moving Head Wash Beam Stage Light. Please read these instructions thoroughly before installation and use, and retain them for future reference.

2. Saugos informacija

• Elektros sauga: Įsitikinkite, kad maitinimo šaltinis atitinka tūrįtage requirements (AC90-260V 50/60Hz). Always disconnect power before servicing or cleaning.
• Montavimas: Install the fixture in a well-ventilated area, away from heat sources. Ensure secure mounting using the provided Omega clamp and safety attachment point.
• Veikimas: Do not look directly into the light source. Avoid operating in environments exceeding 45°C (113°F) or below -20°C (-4°F).
• Priežiūra: Refer to the maintenance section for cleaning and care instructions. Only qualified personnel should perform repairs.

3. Produkto ypatybės

• 36PCS 10W 4-IN-1 RGBW LEDs for vibrant color mixing.
• Motorized linear zoom from 8° to 60° for versatile beam control.
• High light output: 1130LUX (8°) and 320LUX (50°) @5M at full RGBW.
• 50,000 hours lifespan and low power consumption (370W).
• High efficiency LED shutter with variable speed, smooth LED dimmer, LED rainbow effect, macros, and strobe effect (25 flashes per second).
• Control via DMX512 (22 channels), master-slave, sound activated, or auto operation.
• Blue LCD display for easy configuration.
• Lower noise and efficient FAN cooling system.
• Powercon IN/OUT and 3-Pin DMX connectors IN/OUT.
• IP20 apsaugos klasė.

4. Pakuotės turinys

Išpakuodami patikrinkite, ar visi daiktai yra ir yra geros būklės:

• Boulder Pro 36x10W RGBW LED Moving Head Wash Beam Stage Light unit(s)
• 1/4 turn fastening Omega clamp
• Saugos tvirtinimo taškas
• Powercon cable
• DMX kabelis

5. Sąrankos instrukcijos

5.1. Fizinis įrengimas

Mount the light securely using the provided Omega clamp to a truss or suitable overhead structure. Always attach the safety attachment point to prevent accidental falls. Ensure adequate clearance for movement and ventilation.

5.2. Elektros jungtys

Connect the power cable to the Powercon IN port on the rear of the unit. For daisy-chaining power to multiple units, use the Powercon OUT port. Connect DMX control cables to the 3-Pin DMX IN/OUT ports for signal transmission.

5.3. Valdymo režimo pasirinkimas

The fixture supports DMX512, master-slave, sound activated, and auto operation modes. Use the blue LCD display on the base of the unit to navigate menus and select your desired control mode and DMX address if applicable.

6. Naudojimo instrukcijos

6.1. DMX valdymas

The Boulder Pro 36x10W utilizes 22 DMX channels. Refer to the DMX chart (not provided in this manual, typically found in a separate DMX protocol document) for specific channel assignments for pan, tilt, color (RGBW), zoom, dimmer, strobe, and effects. Ensure your DMX controller is configured correctly to match the fixture's DMX address and channel layout.

6.2. Standalone Operation (Auto/Sound Activated)

In auto mode, the fixture will cycle through pre-programmed light shows. In sound-activated mode, the light will react to ambient sound via its built-in microphone. These modes are selected via the LCD display.

6.3. Key Features in Operation

• Spalvų maišymas: Achieve a wide spectrum of colors through RGBW mixing.
• Mastelio keitimas: Adjust the beam angle from a narrow 8° spot to a wide 60° wash.
• Pritemdymas: Smooth 0-100% electronic dimming.
• Strobe: Variable speed strobe effect up to 25 flashes per second.
• Efektai: Utilize LED rainbow effect and pre-programmed macros for dynamic lighting.

6.4. Produkto demonstracinis vaizdo įrašas

7. Priežiūra

Reguliarus šviestuvo remontas užtikrina optimalų veikimą ir ilgaamžiškumą.

• Valymas: Periodically clean the lenses and exterior with a soft, lint-free cloth. Avoid abrasive cleaners.
• Ventiliatorius ir ventiliacijos angos: Ensure cooling fans and ventilation openings are free from dust and debris to maintain efficient cooling.
• Patikra: Regularly check all cables, connections, and mounting hardware for signs of wear or damage.

8. Problemų sprendimas

Jei kyla problemų, peržiūrėkite toliau pateiktas dažniausiai pasitaikančias problemas ir jų sprendimus:

9. Specifikacijos

10. Garantija ir palaikymas

For warranty information or technical support, please contact Boulder Lighting directly. Keep your purchase receipt as proof of purchase. The manufacturer is Guangzhou Baide Lighting LTD.