„Intermatic ET2705C“ elektroninio laikmačio naudojimo instrukcija

Įvadas

This manual provides detailed instructions for the installation, setup, operation, and maintenance of your Intermatic ET2705C Electronic Timer. This device is designed for precise control of electrical loads with its 7/365-day operation mode and single channel output. Please read this manual thoroughly before installation and use to ensure safe and efficient operation.

Svarbios saugos instrukcijos

Figure 1: Front panel of the Intermatic ET2705C Electronic Timer. This image displays the digital display, control buttons (MODE, DAY, ENTER/NEXT, ON/OFF, CLEAR MEM, CLEAR ENTRY, +, -), and important safety warnings in English, French, and Spanish regarding electrical shock and fire hazards, as well as wiring instructions.

Sąranka ir diegimas

1. Montavimas

• The Intermatic ET2705C timer is designed for surface mounting.
• Ensure the mounting location is suitable for a metal enclosure and provides adequate ventilation.
• Securely fasten the timer to a flat, stable surface using appropriate hardware.

2. Laidai

1. Before beginning any wiring, ensure all power to the circuit is disconnected at the main breaker or disconnect switch. Verify with a voltage testeris.
2. Open the timer enclosure. Locate the terminal block.
3. To access the wiring terminals, lift and remove the screw, then swing the plastic insulator covering the terminal block aside as indicated on the unit.
4. Connect the appropriate copper conductors to the terminals as per the wiring diagram provided inside the unit and local electrical codes. This unit supports 120 to 277Vac voltage.
5. Once wiring is complete, replace the plastic insulator covering the terminal block and secure it with the screw.
6. Close the timer enclosure.

3. Pradinis įjungimas

• Restore power to the circuit. The timer display should illuminate.
• Allow the internal capacitor to charge for a few minutes. The timer has a 100-hour backup time in case of power loss.

Naudojimo instrukcijos

Valdymo mygtukai viršujeview:

• MODE: Cycles through different programming modes (e.g., time setting, program setting).
• DIENA: Selects the day of the week during time setting or program scheduling.
• ENTER/NEXT: Patvirtina pasirinkimus ir pereina prie kito nustatymo.
• ĮJUNGTA/IŠJUNGTA: Manual override for immediate ON/OFF control.
• CLEAR MEM: Clears all programmed settings.
• CLEAR ENTRY: Clears the current entry during programming.
• +: Increases values (e.g., hour, minute, program number).
• -: Decreases values (e.g., hour, minute, program number).

1. Dabartinio laiko ir datos nustatymas

1. Paspauskite REŽIMAS button until the time setting mode is displayed.
2. Naudokite + or - mygtukais nustatykite valandas, tada paspauskite ENTER/KITAS.
3. Repeat for minutes and AM/PM (if applicable).
4. Naudokite DIENA button to select the current day of the week, then press ENTER/KITAS patvirtinti.

2. Programming Schedules (7/365 Day Operation)

The timer supports up to 96 ON/OFF cycles. Each program consists of an ON time and an OFF time.

1. Paspauskite REŽIMAS button until "PROG" or "PROGRAM" is displayed.
2. Ekrane bus rodoma „1 ON“. Naudokite + or - to set the desired ON time (hour and minute), then press ENTER/KITAS.
3. Naudokite DIENA button to select the days of the week for this program (e.g., Mon-Fri, Sat-Sun, or individual days). Press ENTER/KITAS.
4. The display will then show "1 OFF". Set the desired OFF time using + or -, tada paspauskite ENTER/KITAS.
5. Repeat steps 2-4 for additional programs.
6. Norėdami išeiti iš programavimo režimo, paspauskite REŽIMAS kol bus rodomas dabartinis laikas.

3. Rankinis nepaisymas

Paspauskite ĮJUNGTA/IŠJUNGTA button to manually switch the connected load ON or OFF, overriding the current program. The timer will resume programmed operation at the next scheduled event.

Priežiūra

• Ensure power is disconnected before performing any maintenance.
• Reguliariai tikrinkite laikmatį, ar nėra kokių nors pažeidimų ar atsilaisvinusių jungčių.
• Prietaiso išorę valykite minkšta, sausa šluoste. Nenaudokite abrazyvinių valiklių ar tirpiklių.
• The internal capacitor provides backup power for up to 100 hours during power outages. No user maintenance is required for the backup device.

Trikčių šalinimas

Specifikacijos

Informacija apie garantiją

For detailed warranty information, please refer to the official Intermatic website or the warranty card included with your product. General warranty terms typically cover defects in materials and workmanship for a specified period from the date of purchase.

Pagalba klientams

If you require technical assistance or have questions regarding your Intermatic ET2705C Electronic Timer, please visit the official Intermatic website for support resources, FAQs, and contact information. You may also refer to the contact details provided on the product packaging.