Tackform Enduro Series 3.5-inch Aluminum Dual Articulating Arm

1. Produktas baigtasview

The Tackform Enduro Series 3.5-inch Aluminum Dual Articulating Arm is designed for versatile device mounting. It features dual articulating 20mm ball sockets and thumbscrews for quick and precise adjustments. This arm is a core component of the Tackform Enduro Series, an ecosystem of mounting solutions.

• Suderinamumas: Fully compatible with all Tackform Enduro Series 20mm components, including suction cups, table clamps, headrest clamps, and various device holders (phones, tablets, action cameras).
• Konstrukcija: Constructed entirely from aluminum for durability and strength. Thumbscrews are made of ABS Plastic.
• Ilgis: Total arm length is 3.5 inches.
• Artikuliacija: Dual ball and socket joints provide multiple points of articulation for optimal device positioning.
• Universalumas: Can be used to replace existing arms for different lengths or to add articulation points with ball-to-ball adapters.

2. Komponentai

The Tackform Dual Articulating Arm consists of a central aluminum arm with two 20mm ball sockets at each end. Each socket is secured by a thumbscrew for independent adjustment.

Figure 1: The Tackform 3.5-inch Aluminum Dual Articulating Arm.

Figure 2: The 3.5-inch length of the articulating arm.

Figure 3: The arm is compatible with 20mm Enduro Series components.

3. Sąranka ir diegimas

To set up your Tackform Dual Articulating Arm, follow these steps:

1. Loosen Thumbscrews: Gently loosen the thumbscrews on both ends of the arm to allow the ball sockets to open.
2. Insert Ball Mounts: Insert your desired 20mm ball mounts (e.g., a base mount and a device holder) into each socket. Ensure the balls are fully seated within the sockets.
3. Tighten Thumbscrews: Hand-tighten the thumbscrews to secure the ball mounts. Do not overtighten.
4. Koreguoti padėtį: Loosen one thumbscrew slightly to adjust the angle of that specific ball joint. Once the desired angle is achieved, re-tighten the thumbscrew. Repeat for the other joint if necessary.

For a visual guide on attaching and securing the arm, please refer to the official product overview vaizdo įrašas žemiau.

Additional demonstrations of 20mm ball arm functionality can be seen in the following videos:

4. Operacija

The dual articulating design allows for flexible positioning of your mounted device. Each thumbscrew independently controls the tightness of its respective ball socket, enabling precise adjustments without affecting the other joint.

Figure 4: The arm allows for 180-degree rotation at each joint.

Figure 5: The ball joints enable full 360-degree rotation for optimal viewkampų.

To adjust the arm:

1. Atlaisvinti: Turn the desired thumbscrew counter-clockwise to loosen the grip on the ball.
2. Padėtis: Adjust the angle and orientation of the attached device or base.
3. Saugus: Turn the thumbscrew clockwise to tighten and secure the ball in its new position. Ensure it is firm to prevent movement during use.

Figure 6: The arm can be used in various configurations, such as mounting an action camera or a tablet.

5. Priežiūra

To ensure the longevity and optimal performance of your Tackform Dual Articulating Arm, consider the following maintenance tips:

• Valymas: Wipe the aluminum arm and ABS plastic thumbscrews with a soft, damp cloth to remove dust and grime. Avoid abrasive cleaners or solvents that could damage the finish.
• Patikra: Periodically inspect the arm and thumbscrews for any signs of wear, damage, or loosening.
• Sandarumas: Ensure all thumbscrews are adequately tightened before each use to prevent accidental movement or detachment of your device.

6. Problemų sprendimas

If you encounter any issues with your Tackform Dual Articulating Arm, please consider the following:

• Ranka nelaiko pozicijos: Ensure both thumbscrews are fully tightened. If using a rubberized ball, confirm it is properly seated within the socket.
• Koregavimo sunkumai: Loosen the thumbscrews sufficiently to allow free movement of the ball joints. If the arm is new, it may require a few adjustments to loosen up.
• Suderinamumo problemos: Verify that all connected components are 20mm ball compatible. This arm is specifically designed for 20mm ball systems.

7. Specifikacijos

8. Garantija ir palaikymas

This product is manufactured by Tackform. For any warranty claims, technical support, or product inquiries, please contact Tackform directly through their official customer service channels. Refer to the product packaging or the Tackform websvetainę, kurioje rasite naujausią kontaktinę informaciją.