Rx Clear 16" Inch Sand Filter User Manual

1. Įvadas

This manual provides essential information for the safe and efficient operation, installation, and maintenance of your Rx Clear 16" Inch Sand Filter. Designed for above-ground pools, this filter system ensures crystal clear water by effectively removing debris and impurities. Please read this manual thoroughly before installation and use to ensure proper setup and longevity of your equipment.

2. Saugos informacija

ĮSPĖJIMAS: Nesilaikant šių nurodymų, galima sunkiai susižaloti arba mirti.

• Always disconnect power to the pump before performing any service or maintenance on the filter system.
• Įsitikinkite, kad visas elektros jungtis atlieka kvalifikuotas elektrikas ir kad laikomasi vietinių taisyklių.
• Nenaudokite filtro, jei kuri nors dalis yra pažeista arba jos trūksta.
• Never attempt to open or service the filter while it is under pressure. Always relieve pressure before opening.
• Laikykite vaikus atokiau nuo baseino įrangos.
• Use only clean, graded filter sand as specified in this manual.
• Dirbdami su baseino cheminėmis medžiagomis, užtikrinkite tinkamą vėdinimą.

3. Komponentai ir surinkimas

Your Rx Clear 16" Sand Filter system includes the following main components:

• Filter Tank (16" diameter)
• Universali bazė
• 6-Position Multi-Port Valve (Top Mount)
• Slėgio matuoklis
• Two 6-foot Hoses
• One 3-foot Hose
• Required Clamps and Fittings

3.1. Diegimo žingsniai

1. Filtro išdėstymas: Place the universal base on a firm, level surface, preferably concrete, as close to the pool as possible. Ensure there is adequate space around the filter for maintenance and operation.
2. Assembling the Tank and Base: Carefully place the filter tank onto the universal base. Ensure it is seated securely.
   

   Image: The Rx Clear 16-inch sand filter unit, showing the tank, multi-port valve on top, and the universal base. This image illustrates the main components assembled.
3. Filtro smėlio įpylimas:
   • Nuimkite daugiafunkcinį vožtuvą nuo bako viršaus.
   • Cover the standpipe opening inside the tank to prevent sand from entering it. A small cup or plastic bag can be used.
   • Carefully pour approximately 110 lbs of #20 silica sand (0.45-0.55 mm) into the filter tank. Distribute the sand evenly.
   • Remove the cover from the standpipe.
4. Installing the Multi-Port Valve:
   • Ensure the O-ring is properly seated on the valve.
   • Carefully lower the multi-port valve onto the tank, aligning the standpipe with the valve's opening. Do not force it.
   • Secure the valve to the tank using the provided clamp or bolts. Ensure a tight, leak-free seal.
   • Install the pressure gauge into the designated port on the valve. Neperveržkite matuoklio.
5. Žarnų prijungimas:
   • Connect the pool pump's discharge port to the "PUMP" port on the multi-port valve using one of the 6-foot hoses and clamps.
   • Connect the "RETURN" port on the multi-port valve to the pool's return inlet using the other 6-foot hose and clamps.
   • Connect the "WASTE" port on the multi-port valve to a suitable waste line or discharge area using the 3-foot hose and clamps. Ensure the waste line directs water away from the pool area and complies with local regulations.
   • Ensure all connections are secure and leak-free. The filter is designed to accept most standard pool pumps and plumbing configurations, including 1.5-inch PVC pipes.
6. Siurblio užpildymas: Before starting the filter, ensure the pool pump is primed according to its manufacturer's instructions.

4. Filtrų sistemos valdymas

The 6-position multi-port valve allows for various operational modes. Always turn off the pump before changing the valve position to prevent damage.

To begin normal filtration, ensure the pump is off, set the valve to FILTRAS, then turn on the pump. Note the initial pressure gauge reading; this is your clean filter pressure.

5. Priežiūra

5.1. Backwashing

Backwash your filter when the pressure gauge reads 8-10 PSI above its clean starting pressure, or when water flow to the pool noticeably decreases. This indicates that the sand bed has accumulated debris and needs cleaning.

1. Išjunkite baseino siurblį.
2. Rotate the multi-port valve handle to the ATGALINĖS PLOVIMAS padėtis.
3. Turn on the pump and backwash for approximately 2-3 minutes, or until the water flowing out of the waste line appears clear.
4. Išjunkite siurblį.
5. Rotate the multi-port valve handle to the IŠSKALAUTI padėtis.
6. Turn on the pump and rinse for 30-60 seconds.
7. Išjunkite siurblį.
8. Rotate the multi-port valve handle back to the FILTRAS padėtis.
9. Įjunkite siurblį, kad atnaujintumėte įprastą filtravimą.

5.2. Sand Replacement

Filter sand typically needs to be replaced every 3-5 years, depending on usage and water quality. Over time, sand particles can become worn and less effective at filtering. Consult a pool professional if you are unsure.

5.3. Pasiruošimas žiemai

For colder climates, proper winterization is crucial to prevent damage to your filter system:

• Kruopščiai nuplaukite ir išskalaukite filtrą.
• Išleiskite visą vandenį iš filtro bako, atidarydami išleidimo kamštį apačioje.
• Remove the multi-port valve and store it in a warm, dry place.
• Nuimkite manometrą.
• Store hoses in a dry place.
• Leave the drain plug open during winter to allow any remaining moisture to escape.

6. Problemų sprendimas

7. Specifikacijos

• Modelio numeris: AC166GSLB
• Bako skersmuo: 16 colių
• Smėlio talpa: Approximately 110 lbs (#20 Silica Sand)
• Gaminio matmenys: 29.5 x 21.5 x 18 colio
• Prekės svoris: 27.5 svaro
• Vožtuvo tipas: 6-Position Multi-Port (Top Mount)
• Gamintojas: Rx Aišku
• Kilmės šalis: JAV

8. Garantija ir palaikymas

For warranty information, technical support, or to order replacement parts, please contact Rx Clear customer service. Keep your purchase receipt and model number (AC166GSLB) readily available when contacting support.

For more information and products, visit the official Rx Clear store: Rx Clear Store on Amazon