ErGear Dual Monitor Desk Mount EGCM13B Instruction Manual

Įvadas

Thank you for choosing the ErGear Dual Monitor Desk Mount. This manual provides detailed instructions for the safe and efficient installation, operation, and maintenance of your new monitor mount. Please read this manual thoroughly before installation and keep it for future reference.

Svarbi saugos informacija

Please ensure all instructions are read and understood before assembly and use. If you have any questions, please contact customer service. Failure to follow these instructions may result in property damage, serious injury, or death.

Verify that your monitor's weight and VESA pattern are within the specified limits.
Do not exceed the maximum load capacity of 26.5 lbs per arm.
Ensure the mounting surface (desk) is strong enough to support the combined weight of the mount and monitors.
Use only the provided hardware.
Smulkias dalis laikykite vaikams nepasiekiamoje vietoje.

Specifikacijos

Modelis: EGCM13B
Ekrano dydžio suderinamumas: Nuo 13 iki 34 colių
Weight Capacity (per arm): Iki 26.5 svarų
VESA suderinamumas: 75 x 75 mm, 100 x 100 mm
Arm Span: 33 colių
Stulpo aukštis: 16.3 colių
Judėjimo tipas: Tilt, Swivel, Rotation, Articulating
Maksimalus pakreipimo kampas: 90 laipsnių
Medžiaga: Legiruotasis plienas
Spalva: Juoda
Montavimo tipas: Stalinis laikiklis (C-Clamp arba žiedas)
C-Clamp Stalo storis: 0.39 colio – 3.15 colio
Grommet Mount Desk Thickness: 0.39 colio – 2.17 colio
Žiedinės įvorės skylės skersmuo: 0.47 colio – 0.79 colio

Pakuotės turinys

Please check that all parts are included and undamaged. If any parts are missing or damaged, please contact customer service.

Pagrindinis stulpas su stalo kabinaamp/Grommet Base
Dvigubo monitoriaus rankenos
VESA plokštės (2 vnt.)
Tvirtinimo detalės (varžtai, poveržlės, įrankiai)
Kabelių valdymo spaustukai
Instrukcijų vadovas

ErGear Dual Monitor Desk Mount components laid out — Image: All components of the ErGear Dual Monitor Desk Mount laid out, including the main pole, dual arms, VESA plates, and various hardware for assembly.

Sąranka ir diegimas

1. Desk Compatibility Check

Before installation, ensure your desk meets the following criteria:

Medžiaga: Recommended for wooden tables.
Apatinė dalis: Preferably free of beams or panels that may interfere with installation.
C-Clamp Storis: 0.39 colio – 3.15 colio
Grommet Mount Thickness: 0.39" - 2.17" (Hole Diameter: 0.47" - 0.79")

2. Monitor Compatibility Check

Each monitor must meet these conditions:

Ekrano dydis: Nuo 13 iki 34 colių
Svoris: Iki 26.5 svarų
VESA tvirtinimo angos: 75x75 mm or 100x100 mm apart on the back of the monitor.

Diagram showing VESA hole patterns on the back of a monitor — Image: Illustration of VESA mounting hole patterns (75x75mm and 100x100mm) on the back of a monitor, indicating where the mount attaches. It also shows how to remove a monitor's original stand.

3. Assemble the Pole with Clamp Palaikymas

Choose either C-Clamp or Grommet installation based on your desk type.

Video: Demonstrates the installation process of the dual monitor desk mount, including assembling the pole with clamp support for both grommet and C-clamp methods. This video is provided by the seller.

Diagrama, rodanti C-Clamp ir įvorės tvirtinimo parinktys — Image: Visual guide illustrating the two available mounting options: C-Clamp for desk edges and Grommet mount for desks with existing holes. Includes dimensions for compatible desk thickness and hole diameter.

Follow the detailed steps in the provided video and diagrams to securely attach the main pole to your desk using either the C-Clamp or Grommet method. Ensure all screws are tightened appropriately for stability.

4. Assemble the Arm and Pole Wire Clips

Attach the monitor arms to the main pole. Loosen the screw on the pipe clamp before installing the arm, then tighten it securely. Ensure the VESA plate side of the arm faces upwards. Install the cable management clips along the arms and pole.

5. Assemble VESA Plate and Monitor

Attach the VESA plate to the back of your monitor using the appropriate screws and washers. Ensure it is securely fastened.

6. Install the Monitor to the Swivel Arm

Carefully slide the monitor (with the attached VESA plate) onto the swivel arm. Secure it by tightening the locking screw. Adjust the screw with the Allen key to adjust the height of the VESA panel as needed (clockwise to lower, counter-clockwise to raise).

Image showing two monitors mounted on the ErGear Dual Monitor Desk Mount — Image: Two monitors securely mounted on the ErGear Dual Monitor Desk Mount, demonstrating a clean and organized workspace.

Valdymas ir reguliavimas

The ErGear Dual Monitor Desk Mount offers versatile adjustments for optimal viewkomfortas:

Aukščio reguliavimas: Atlaisvinkite klamp on the main pole to slide the arms up or down to your desired height. Re-tighten the clamp saugiai.
Pakreipti: Adjust the monitor's vertical angle by tilting it +/-45 degrees to reduce glare and eye strain.
Sukamasis: Rotate the monitor horizontally +/-90 degrees for easy screen sharing or viewiš skirtingų kampų.
Pasukimas: Pasukite monitorių 360 laipsnių kampu, kad perjungtumėte horizontalią ir vertikalią orientacijas.
Arm Extension/Retraction: The articulating arms allow you to extend or retract your monitors closer or further from you. Adjust the tension screws on the arm joints as needed to hold the desired position.

Diagrama, rodanti pakreipimo, pasukimo ir sukimosi reguliavimą — Image: Visual representation of the monitor's flexible adjustments, including +/-45° tilt, +/-90° swivel, and 360° rotation, allowing for ergonomic positioning.

Priežiūra

Periodiškai patikrinkite visus varžtus ir jungtis, kad jie būtų tvirtai priveržti ir užtikrinti jų tvirtumą.
Laikiklį valykite minkšta šluoste,amp audinys. Venkite abrazyvinių valiklių.
Do not disassemble the mount unless instructed to do so.

Trikčių šalinimas

Monitoriai nėra lygūs: Ensure the VESA plates are correctly aligned and tightened. Adjust the small bolts on the tilt head to fine-tune alignment.
Monitors sag or do not hold position: Tighten the tension screws on the arm joints. Refer to the assembly instructions for specific locations.
Laikiklis atrodo nestabilus: Double-check that the C-Clamp or Grommet mount is securely fastened to the desk and all screws are fully tightened. Ensure your desk meets the thickness requirements.

Garantija ir palaikymas

For warranty information or technical support, please refer to the product packaging or contact ErGear customer service directly. Keep your purchase receipt as proof of purchase.

ErGear EGCM13B