„Seco-Larm SK-910RD1“ radijo imtuvo naudojimo instrukcija

1. Įvadas

The Seco-Larm SK-910RD1 is a 1-channel RF receiver designed to remotely control various devices such as garage doors, lights, motorized gates, and lifts. It features flexible operating voltage, extended range capabilities, and pushbutton programming for ease of use.

This manual provides detailed instructions for the installation, programming, operation, and maintenance of your SK-910RD1 RF Receiver.

2. Saugos informacija

• Prieš montuodami ir naudodami atidžiai perskaitykite visas instrukcijas.
• Prieš atlikdami bet kokius laidų prijungimo ar techninės priežiūros darbus, įsitikinkite, kad maitinimas yra atjungtas.
• Installation should be performed by qualified personnel to prevent damage or injury.
• Nelaikykite prietaiso nuo drėgmės ar ekstremalių temperatūrų.
• Use only specified power sources (10-24 VAC/VDC).

3. Pakuotės turinys

• 1x SK-910RD1 RF Receiver
• Instrukcijų vadovas

4. Pagrindinės savybės

• Lankstus 10~24 VAC/VDC darbinis tūristage.
• Operating range up to 500 feet (150m), extendable to 1,000 feet with an optional extended range antenna.
• Independently programmable channels, supporting up to 15 transmitter button codes per channel.
• Pushbutton programming eliminates the need for jumpers or switches.
• Five selectable output modes per channel: timed pulse (0.5-99 seconds), timed pulse (1-99 minutes), toggle, latch, and follow (validity).
• Compatible with all ENFORCER SK-series transmitters operating at the receiver's base frequency (315MHz).

5. Sąranka ir diegimas

5.1 Komponento identifikavimas

1 paveikslas: Baigėsiview of the SK-910RD1 RF Receiver. The image shows the black casing, a green terminal block with screw terminals for wiring, a red 7-segment LED display, and a small black programming pushbutton.

The receiver features a terminal block for power and relay connections, a 2-digit 7-segment LED display for programming feedback, and a programming pushbutton.

5.2 Laidai

Connect the power supply (10-24 VAC/VDC) to the appropriate terminals. The relay output provides Form C contacts (Normally Open, Normally Closed, Common) for connecting to the controlled device. Refer to the device's manual for specific wiring requirements.

• Maitinimo įvestis: Connect 10-24 VAC/VDC to the '+' and '-' terminals.
• Relės išėjimas: Use the NO (Normally Open), NC (Normally Closed), and COM (Common) terminals to connect to your control circuit. The relay is rated for 10A@14VDC.

5.3 Montavimas

The receiver can be mounted using screws through the integrated mounting tabs on the casing. Choose a location that is protected from environmental elements and allows for optimal RF signal reception.

6. Naudojimo instrukcijos

6.1 Siųstuvų programavimas

The SK-910RD1 uses pushbutton programming. Up to 15 transmitter button codes can be programmed per channel.

1. Įeikite į programavimo režimą: Press and hold the programming button until the LED display shows "P".
2. Pasirinkite kanalą: Press the programming button repeatedly to cycle through channels (e.g., "C1" for Channel 1).
3. Learn Transmitter: While the desired channel is displayed, press the button on the transmitter you wish to program. The LED will flash to confirm successful learning.
4. Išeiti iš programavimo režimo: Wait for approximately 10 seconds without any input, or press and hold the programming button until the display turns off.

Pastaba: If the memory for a channel is full, the LED will indicate an error. To clear a single transmitter or all transmitters, refer to the advanced programming section in the full manual (if available).

6.2 Selecting Output Modes

The receiver supports five output modes per channel: timed pulse (0.5-99 seconds), timed pulse (1-99 minutes), toggle, latch, and follow (validity). The default mode is 1-second timed pulse.

1. Enter Mode Selection: Press and hold the programming button until "P" appears, then release. Press again briefly to cycle to "M".
2. Pasirinkite kanalą: Press the programming button repeatedly to select the desired channel (e.g., "C1").
3. Ciklo režimai: Once the channel is selected, press the programming button briefly to cycle through the available output modes. The LED display will show an indicator for each mode (e.g., "tP" for timed pulse, "tG" for toggle, "Lt" for latch, "Fo" for follow).
4. Set Time (for Timed Pulse): If a timed pulse mode is selected, the display will show a numerical value. Press the programming button to adjust the time.
5. Patvirtinti ir išeiti: Wait for approximately 10 seconds for the setting to be saved and the receiver to exit programming mode.

7. Priežiūra

• Keep the receiver clean and free from dust.
• Periodically check wiring connections for security.
• Ensure the receiver is not obstructed, which could affect RF signal reception.
• Viduje nėra naudotojo prižiūrimų dalių. Kreipkitės į aptarnavimą kvalifikuotam personalui.

8. Problemų sprendimas

9. Specifikacijos

• Modelis: SK-910RD1
• Veikimo dažnis: 315 MHz
• Atminties talpa: 15 transmitters per channel
• Veiklos ttage: 10-24 VAC/VDC
• Veikimo srovė:
  • Standby: 16mA@12VDC, 12mA@24VDC
  • Active: 60mA@12VDC, 50mA@24VDC (per channel)
• Relės išvesties režimai: Timed pulse (0.5-99 sec, 1-99 min), Toggle, Latch, Follow (validity)
• Relės kontaktai: 1x Form C, 10A@14VDC
• Jungtys: Screw terminals (+, -, NO, NC, COM)
• Skaitmeninis ekranas: 2 skaitmenų, 7 segmentų šviesos diodas
• Bendri matmenys: 4.21 x 0.90 x 2.36 colio (107 x 23 x 60 mm)
• Prekės svoris: 3.2 uncijos (90.7 gramų)

10. Garantija ir palaikymas

For warranty information and technical support, please contact Seco-Larm customer service or visit their official websvetainę. Išsaugokite pirkimo čekį garantiniams reikalavimams.

Gamintojas: Seco-Larm