CISCO ESW6300 USB prievado įjungimas prieigos taškuose

Specifikacijos

• USB Port Power: Up to 2.5W (some models support up to 4.5W)
• USB prievado funkcija: maitinimo šaltinis USB įrenginiams

Produkto naudojimo instrukcijos

USB prievado įjungimas prieigos taškuose:
To enable the USB port on your Cisco Access Point for powering USB devices:

1. Check if your AP model supports a USB power source by referring to the datasheet.
2. AP Pro konfigūravimasfile naudojant CLI:
   • Įjunkite visuotinį konfigūracijos režimą: configure terminal
   • Sukurkite AP profesionaląfile: ap profile xyz-ap-profile
   • Įjunkite USB AP profile: usb-enable
   • Išeiti iš konfigūracijos režimo: end
3. Konfigūruokite prieigos taško USB nustatymus naudodami CLI:
   • Įveskite privilegijuotą EXEC režimą: enable
   • Enable the USB port on the AP: ap name AP44d3.xy45.69a1 usb-module override

USB prievadas kaip prieigos taškų maitinimo šaltinis
Some Cisco APs have a USB port that can act as a source of power for some USB devices. The power can be up to 2.5W; if a USB device draws more than 2.5W of power, the USB port shuts down automatically. The port is enabled when the power draw is 2.5W or lower. Refer to the datasheet of your AP to check if the AP has a USB port that can act as a source of power.

Pastaba 
Both IW6300 and ESW6300 APs have a USB port that can act as a source of power up to 4.5W for some USB devices.

Pastaba
The controller records the last five power-overdrawn incidents in its logs.

Atsargiai

When an unsupported USB device is connected to the Cisco AP, the following message is displayed:
The inserted USB module is not a supported device. The behaviour of this USB device and its impact on the Access Point are not guaranteed. If Cisco determines that a fault or defect can be isolated due to the use of third-party USB modules installed by a customer or reseller, Cisco may withhold support under warranty or the support program under contract. In the course of providing support for Cisco networking products, the end user may be required to install Cisco-supported USB modules in the event Cisco determines that removing third-party parts will assist Cisco in diagnosing the root cause for troubleshooting purposes. Cisco also reserves the right to charge the customer per the then-current time and material rates for services provided to the customer when Cisco determines, after having provided such services, that an unsupported device caused the root cause of the defective product.

AP Pro konfigūravimasfile (CLI)

Procedūra

	Komanda arba veiksmas	Tikslas
1 veiksmas	sukonfigūruoti terminalą ExampLe: Įrenginio Nr. konfigūravimo terminalas	Įjungiamas visuotinio konfigūravimo režimas.
2 veiksmas	ap profileAP- Profilee ExampLe: Įrenginio (konfigūracijos) Nr. ap profile xyz-ap-profile	Konfigūruoja AP profile and enters the AP profile konfigūravimo režimas. Pastaba When you delete a named profile, the APs associated with that profile will not revert to the default profile.
3 veiksmas	usb-enable ExampLe: Įrenginys (config-ap-profile)# usb-enable	Įgalina USB kiekvienam AP profesionaluifile. Pastaba By default, the USB port on the AP is disabled.   Naudokite no USB-Enable command to disable USB for each AP profile.
4 veiksmas	pabaiga ExampLe: Įrenginys (config-ap-profile)# pabaiga	Grįžta į privilegijuotą EXEC režimą. Arba galite paspausti Ctrl-Z Norėdami išeiti iš visuotinio konfigūravimo režimo.

Prieigos taško (CLI) USB nustatymų konfigūravimas

Procedūra

	Komanda arba veiksmas	Tikslas
1 veiksmas	įjungti ExampLe: Įrenginio Nr. įjungti	Įjungia privilegijuotąjį EXEC režimą.
2 veiksmas	ap vardas ap-vardas usb-module ExampLe: Įrenginio Nr. ap name AP44d3.xy45.69a1 usb-module	Enables the USB port on the AP. Naudokite ap vardas ap-vardas no usb-module Command to disable the USB port on the AP. Pastaba If you are using a Cisco Catalyst 9105AXW AP and you enable the USB port (3at PoE-in), it is not possible to enable the USB PoE-out at the same time.
3 veiksmas	ap vardas ap-vardas usb-module override ExampLe: Įrenginio Nr. ap name AP44d3.xy45.69a1 usb-module override	Overrides the USB status of the AP profile and considers the local AP configuration. Naudokite ap vardas ap-vardas no usb-module override command to override the USB status of the AP and consider the AP profile konfigūracija. Pastaba You can configure the USB status for an AP only if you enable USB override for it.

Prieigos taško (GUI) USB nustatymų konfigūravimas

Procedūra

• 1 veiksmas: pasirinkite Konfigūracija > Belaidis ryšys > Prieigos taškai.
• Step 2: In the Access Points window, click the name of the AP.
• Step :3 In the Edit AP window, click the Interfaces tab.
• Step: 4 In the USB Settings section, configure the USB Module State as either of the following:
  • ENABLED: Enables the USB port on the AP
  • DISABLED: Disables the USB port on the AP
• Pastaba
  If you are using Cisco Catalyst 9105AXW AP and if you enable the USB por3at3at PoE-in, it is not possible to enable the USB PoE-out at the same time.
• Step 5: Configure USB Override as either of the following:
  • ENABLED: Overrides USB status of the AP profile and considers the local AP configuration
  • DISABLED: Overrides USB status of the AP and considers the AP profile konfigūracija
  • Pastaba
    You can configure the USB status for an AP only if you enable USB override for it.
• Step 6: Click Apply & Update to Device.

Prieigos taškų USB konfigūracijų stebėjimas (CLI)

• Į view the inventory details of APs, use the following command: show ap name ap-name inventory
• Toliau pateikiama kaipampišvestis:
  • Device# show ap name AP500F.8059.1620 inventory
  • Device# show ap name AP500F.8059.1620 inventory
• Toliau pateikiama kaipampišvestis:
  • NAME: AP280  DESCR: Cisco Aironet 2800 Series (IEEE 802.11ac) Access Point
  • PID: AIR-AP2802I-D-K9 , VID: 01, SN: XXX1111Y2ZZZZ2800
  • NAME: SanDisk, DESCR: Cruzer Blade
  • PID: SanDisk , SN: XXXX1110010, MaxPower: 224
• Į view the summary of an AP module, use the following command: show ap module summary
• Toliau pateikiama kaipampišvestis:
  • Įrenginio Nr. rodo AP modulio santrauką
• AP Name External Module External Module PID External Module

Aprašymas
AP500F.1111.2222 Enable SanDisk Cruzer Blade

• Į view the USB configuration details for each AP, use the following command: show ap name ap-name config general
• Toliau pateikiama kaipampišvestis:
  • Įrenginio Nr. rodo prieigos taško pavadinimą AP500F.111.2222 konfigūracija bendra
  • USB Module Type……………………………. USB Module
  • USB Module Status………………………….. Disabled
  • USB Module Operational State………………… Enabled
  • USB Override …………………………….. Enabled
• Į view sthe status of the USB module, use the following command: show ap profile pavadinimas xyz išsamus
• Toliau pateikiama kaipampišvestis:
  • Įrenginys Nr. rodo programėlę profile pavadinimas xyz išsamus
  • USB Module: ENABLED

DUK

Q: How can I tell if my AP supports a USB power source?

A: You can refer to the datasheet of your AP to check if it has a USB port that can act as a power source for USB devices.

K: Kas nutinka, jei prijungtas USB įrenginys sunaudoja daugiau nei 2.5 W energijos?

A: If a USB device draws more than 2.5W of power, the USB port shuts down automatically to prevent damage.

Dokumentai / Ištekliai

CISCO ESW6300 USB prievado įjungimas prieigos taškuose [pdfNaudojimo instrukcija IW6300, ESW6300, ESW6300 USB prievado įjungimas prieigos taškuose, USB prievado įjungimas prieigos taškuose, USB prievadas prieigos taškuose, Prieigos taškai

Nuorodos

• Vartotojo vadovas