THIRD REALITY ZB2 Smart Button User Manual

Smart Button ZB2
Greitos pradžios vadovas

Pakuotės turinys

Specifikacijos

Atstatyti gamyklinius nustatymus

Press and hold buttons 1 and 2 for 10 seconds until the device beeps three times, indicating that it is in pairing mode.

Setting up your Smart Button ZB2

1. Follow instructions to set up your compatible Zigbee hub.
2. Use the Micro-USB charging cable included in the package to connect the button to a power adapter (not included) to active the Smart Button ZB2.
3. You can also press and hold buttons 1 and 2 for 10 seconds, the Smart Button ZB2 will be activated once it beeps three times. The device will automatically enter pairing mode.
   Note: It will exit pairing mode automatically if not successfully paired within 3 minutes, to put it into pairing mode again, press and hold buttons 1 and 2 for 10 seconds until the device beeps three times, indicating that it is in pairing mode.
4. After the pairing is completed, the device will beep once. you can create routines in the corresponding smart home App or platform to control other connected devices. THIRDREALITY Smart Button ZB2 features three buttons (button 1 & button 2 & button  3), each supporting three control settings: Pressed, Double Pressed and Held. Note: When charging, please connect the button to a power adapter (not included) using the Micro-USB charging cable provided in the package. The Smart Button ZB2 will be fully charged until it beep twice.

Nuskaitykite QR kodą į view detales

https://bit.ly/488mkj9

Trikčių šalinimas

1. How to check if the device is fully charged
   The Smart Button ZB2 will be fully charged until it beep twice.
2. Įrenginys neįsijungia
   Recharge the battery, ensure it powers on properly, and note that low temperatures may reduce performance.
3. Cannot charge / No charging response
   Use the original charger, check the charging port, and wait a few minutes in case of over-discharge protection.

FCC reguliavimo atitiktis
Šis įrenginys atitinka FCC taisyklių 15 dalį. Naudojimui taikomos šios dvi sąlygos: (1) šis įrenginys negali sukelti žalingų trukdžių ir (2) šis įrenginys turi priimti bet kokius gaunamus trikdžius, įskaitant trikdžius, kurie gali sukelti nepageidaujamą veikimą.
Bet kokie pakeitimai ar modifikacijos, kurių aiškiai nepatvirtino už atitiktį atsakinga šalis, gali panaikinti vartotojo teisę naudoti įrangą.
Pastaba: Ši įranga buvo išbandyta ir nustatyta, kad ji atitinka B klasės skaitmeninio įrenginio apribojimus pagal FCC taisyklių 15 dalį.
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the  instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by  turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
– Perorientuokite arba perkelkite priėmimo anteną.
– Padidinkite atstumą tarp įrangos ir imtuvo.
– Įjunkite įrangą į kitokios grandinės lizdą, nei prijungtas imtuvas.
– Dėl pagalbos kreipkitės į pardavėją arba patyrusį radijo/televizijos techniką.
The device has been evaluated to meet general RF exposure requirement. The device can be used in the exposure condition without restriction. 06

Dėl ribotos garantijos apsilankykite
https://thirdreality.com/faq-help-center/
Norėdami gauti klientų aptarnavimo, susisiekite su mumis el
info@3reality.com arba apsilankyti www.thirdreality.com
For questions on other platforms, visit the corresponding
platform’s application/support platform.